source: FPGA/FTU/old_design/ftu_board.ucf@ 5458

Last change on this file since 5458 was 251, checked in by qweitzel, 14 years ago
ucf file added to new design
File size: 6.7 KB
Line 
1########################################################
2# FTU Board
3# FACT Trigger Unit
4#
5# Pin location constraints
6#
7# by Patrick Vogler, Quirin Weitzel
8# 01 July 2010
9########################################################
10
11
12#Clock
13#######################################################
14NET ext_clk LOC = Y11 | IOSTANDARD=LVCMOS33; # Clk
15
16
17# RS-485 Interface
18#######################################################
19NET rx_en LOC = T20 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # 485_RE: enable RS-485 receiver
20NET tx_en LOC = U20 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # 485_DE: enable RS-485 transmitter
21NET tx LOC = U19 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # 485_DO: serial data to FTM
22NET rx LOC = R20 | IOSTANDARD=LVCMOS33; # 485_DI: serial data from FTM
23
24
25# Board ID - inputs
26# local board-ID "solder programmable"
27#######################################################
28NET brd_id<0> LOC = C4 | IOSTANDARD=LVCMOS33; # P0
29NET brd_id<1> LOC = C5 | IOSTANDARD=LVCMOS33; # P1
30NET brd_id<2> LOC = C6 | IOSTANDARD=LVCMOS33; # P2
31NET brd_id<3> LOC = C7 | IOSTANDARD=LVCMOS33; # P3
32NET brd_id<4> LOC = C8 | IOSTANDARD=LVCMOS33; # P4
33NET brd_id<5> LOC = B8 | IOSTANDARD=LVCMOS33; # P5
34NET brd_id<6> LOC = C9 | IOSTANDARD=LVCMOS33; # P6
35NET brd_id<7> LOC = B9 | IOSTANDARD=LVCMOS33; # P7
36
37
38# Board Addresses
39# geographical slot address
40#######################################################
41NET brd_add<0> LOC = A15 | IOSTANDARD=LVCMOS33; # ADDR0
42NET brd_add<1> LOC = B15 | IOSTANDARD=LVCMOS33; # ADDR1
43NET brd_add<2> LOC = A16 | IOSTANDARD=LVCMOS33; # ADDR2
44NET brd_add<3> LOC = A17 | IOSTANDARD=LVCMOS33; # ADDR3
45NET brd_add<4> LOC = A18 | IOSTANDARD=LVCMOS33; # ADDR4
46NET brd_add<5> LOC = B18 | IOSTANDARD=LVCMOS33; # ADDR5
47
48
49# DAC SPI Interface
50#######################################################
51NET mosi LOC = E20 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #MOSI: serial data to DAC, master-out-slave-in
52NET sck LOC = E19 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #SCK: serial clock to DAC
53NET cs_ld LOC = E18 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #DAC_CS: chip select or load to DAC
54NET clr LOC = D20 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #DAC_CRL: clear signal to DAC
55
56
57# Testpoints
58######################################################
59# on Connector J5
60NET TP_A<0> LOC = B3 | IOSTANDARD=LVCMOS33; # TP0_0
61NET TP_A<1> LOC = A3 | IOSTANDARD=LVCMOS33; # TP1_0
62NET TP_A<2> LOC = A4 | IOSTANDARD=LVCMOS33; # TP2_0
63NET TP_A<3> LOC = B5 | IOSTANDARD=LVCMOS33; # TP2_0
64
65# on Connector J6
66NET TP_A<4> LOC = A5 | IOSTANDARD=LVCMOS33; # TP4_0
67NET TP_A<5> LOC = A6 | IOSTANDARD=LVCMOS33; # TP5_0
68NET TP_A<6> LOC = B7 | IOSTANDARD=LVCMOS33; # TP6_0
69NET TP_A<7> LOC = A7 | IOSTANDARD=LVCMOS33; # TP7_0
70
71# on Connector J7
72NET TP_A<8> LOC = B11 | IOSTANDARD=LVCMOS33; # TP8_0
73NET TP_A<9> LOC = A12 | IOSTANDARD=LVCMOS33; # TP9_0
74NET TP_A<10> LOC = B12 | IOSTANDARD=LVCMOS33; # TP10_0
75NET TP_A<11> LOC = A14 | IOSTANDARD=LVCMOS33; # TP11_0
76
77
78# Rate counter LVDS Inputs
79######################################################
80# logic signal from first trigger patch
81NET patch_A_p LOC = Y4 | IOSTANDARD=LVDS_33 | DIFF_TERM=No; # LVDS0_P
82NET patch_A_n LOC = Y5 | IOSTANDARD=LVDS_33 | DIFF_TERM=No; # LVDS0_N
83
84# logic signal from second trigger patch
85NET patch_B_p LOC = Y6 | IOSTANDARD=LVDS_33 | DIFF_TERM=No; # LVDS1_P
86NET patch_B_n LOC = Y7 | IOSTANDARD=LVDS_33 | DIFF_TERM=No; # LVDS1_N
87
88# logic signal from third trigger patch
89NET patch_C_p LOC = Y17 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # LVDS2_P
90NET patch_C_n LOC = Y18 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # LVDS2_N
91
92# logic signal from fourth trigger patch
93NET patch_D_p LOC = Y16 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # LVDS3_P
94NET patch_D_n LOC = W16 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # LVDS3_N
95
96#The Trigger Primitive: logic signal from n-out-of-4 circuit
97NET trig_prim_p LOC = Y13 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # TRG_P+
98NET trig_prim_n LOC = W13 | IOSTANDARD=LVDS_33 | DIFF_TERM=No ; # TRG_P-
99
100
101# Enables
102######################################################
103# Patch 0
104NET enables_A<0> LOC = D2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_0
105NET enables_A<1> LOC = B1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_1
106NET enables_A<2> LOC = C2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_2
107NET enables_A<3> LOC = D1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_3
108NET enables_A<4> LOC = C1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_4
109NET enables_A<5> LOC = D4 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_5
110NET enables_A<6> LOC = E1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_6
111NET enables_A<7> LOC = D3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_7
112NET enables_A<8> LOC = E3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; # XEN0_8
113
114## Patch 1
115NET enables_B<0> LOC = F2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_0
116NET enables_B<1> LOC = F4 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_1
117NET enables_B<2> LOC = F3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_2
118NET enables_B<3> LOC = F1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_3
119NET enables_B<4> LOC = G3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_4
120NET enables_B<5> LOC = G4 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_5
121NET enables_B<6> LOC = H2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_6
122NET enables_B<7> LOC = H3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_7
123NET enables_B<8> LOC = J3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN1_8
124
125# Patch 2
126NET enables_C<0> LOC = N1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_0
127NET enables_C<1> LOC = R1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_1
128NET enables_C<2> LOC = M3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_2
129NET enables_C<3> LOC = N2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_3
130NET enables_C<4> LOC = P1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_4
131NET enables_C<5> LOC = N3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_5
132NET enables_C<6> LOC = R2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_6
133NET enables_C<7> LOC = P3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_7
134NET enables_C<8> LOC = T2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN2_8
135
136# Patch 3
137NET enables_D<0> LOC = R3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
138NET enables_D<1> LOC = T4 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
139NET enables_D<2> LOC = T3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
140NET enables_D<3> LOC = U1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
141NET enables_D<4> LOC = U3 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
142NET enables_D<5> LOC = V1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
143NET enables_D<6> LOC = V2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
144NET enables_D<7> LOC = W1 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
145NET enables_D<8> LOC = W2 | IOSTANDARD=LVCMOS33 | SLEW = SLOW; #XEN3_0
Note: See TracBrowser for help on using the repository browser.