source: firmware/FAD/FACT_FAD_lib/hdl/FAD_rs485_receiver.vhd@ 15553

--
-- VHDL Architecture FACT_FAD_lib.rs485_receiver.beha
--
-- Created:
--          by - Benjamin Krumm.UNKNOWN (EEPC8)
--          at - 12:16:57 11.06.2010
--
-- using Mentor Graphics HDL Designer(TM) 2009.2 (Build 10)
--
--
-- modified for FTU design by Q. Weitzel, 13 September 2010
-- timeout added, Q. Weitzel, 26 October 2010
-- 
-- modified for FAD design by D.Neise, 12. April 2011
-- modified library include statements mainly.
--

LIBRARY ieee;
USE ieee.std_logic_1164.all;
USE ieee.std_logic_arith.all;

--library fad_rs485_definitions;
--USE fad_rs485_definitions.fad_rs485_constants.all;
library fact_fad_lib;
use fact_fad_lib.fad_rs485_constants.all;

ENTITY FAD_rs485_receiver IS
  generic(
    -- defined in fad_rs485_definitions.fad_rs485_constants
    RX_BYTES  : integer := RS485_MESSAGE_LEN_BYTES; -- no. of bytes to receive
    RX_WIDTH  : integer := RS485_MESSAGE_LEN_BYTES * 8  -- no. of bits to receive
  );
  port(
    rec_clk   : in  std_logic;
 
        -- Interface to MAX3485:
                rx_d     : IN  std_logic;
                rx_en    : OUT std_logic;
                tx_d     : OUT std_logic;
                tx_en    : OUT std_logic;
        
        
        rec_start : in std_logic;
        rec_timeout_occured : out std_logic := '0';
    rec_dout  : out std_logic_vector(RX_WIDTH - 1 downto 0) := (others => '0');
    rec_valid : out std_logic := '0'
  );
END ENTITY FAD_rs485_receiver;

ARCHITECTURE beha OF FAD_rs485_receiver IS
  
  signal rxcnt                  : integer range 0 to RX_BYTES := 0;
  signal rxsr                   : std_logic_vector(3 downto 0) := (others => '0');
  signal timeout_cnt    : integer range 0 to RS485_TIMEOUT + 1 := 0;
  signal rec_den                : std_logic := '0';
  signal rec_din                : std_logic_vector(7 downto 0) := (others => '0');
  signal start_sr               : std_logic_vector(1 downto 0) := (others => '0');
  signal started                : std_logic := '0'; -- 0-not running; 1-running
  
        component FAD_rs485_interface
        port(
                clk      : IN  std_logic;
                -- RS485
                rx_d     : IN  std_logic;
                rx_en    : OUT std_logic;
                tx_d     : OUT std_logic;
                tx_en    : OUT std_logic;
                -- FPGA
                rx_data  : OUT std_logic_vector (7 DOWNTO 0);
                --rx_busy  : OUT std_logic  := '0';
                rx_valid : OUT std_logic  := '0';
                tx_data  : IN  std_logic_vector (7 DOWNTO 0);
                tx_busy  : OUT std_logic  := '0';
                tx_start : IN  std_logic );
        end component;

  
BEGIN

        Inst_FAD_rs485_interface : FAD_rs485_interface
                port map(
                        clk      => rec_clk,
                        -- RS485
                        rx_d     => rx_d,
                        rx_en    => rx_en,
                        tx_d     => tx_d,
                        tx_en    => tx_en,
                        -- FPGA
                        rx_data  => rec_din,
                        
                        rx_valid => rec_den,
                        tx_data  => "00000000",
                        tx_busy  => open,
                        tx_start => '0'
                );

-- process(rec_clk)
        -- begin
                -- if rising_edge(rec_clk) then
                        -- start_sr <= start_sr(0) & rec_start;
                        -- rxsr <= rxsr(2 downto 0) & rec_den;
                        
                        
                        -- if (start_sr = "01") then
                                -- started <= '1';
                        -- end if;
                        
                        -- if ((rxcnt > 0) or (started = '1')) then
                                -- timeout_cnt <= timeout_cnt + 1;
                        -- else
                                -- timeout_cnt <= 0;
                        -- end if;
                        
                        -- if (timeout_cnt = RS485_TIMEOUT) then
                                -- rxcnt <= 0;
                                -- started <= '0';
                                -- rec_timeout_occured <= '1';
                                -- rec_valid <= '1';
                        -- else
                                -- if (rxsr(3 downto 2) = "01") then -- identify rising edge
                                        -- if (rxcnt = 0) then
                                                -- rec_dout <= (others => '0');
                                        -- end if;
                                        -- rec_dout((rxcnt*rec_din'length + rec_din'length - 1) downto (rxcnt*rec_din'length)) <= rec_din;
                                        -- rxcnt <= rxcnt + 1;
                                        -- if (rxcnt < RX_BYTES - 1) then
                                                -- rec_valid <= '0';
                                                -- rec_timeout_occured <= '0';
                                        -- else
                                                -- rxcnt <= 0;
                                                -- rec_valid <= '1';
                                        -- end if;
                                -- end if;
                        -- end if;
                
                -- end if; --if rising_edge(rec_clk)
        -- end process ;

        
        
        
        process (rec_clk)
        begin
                if rising_edge(rec_clk) then
                        start_sr <= start_sr(0) & rec_start;
                        rxsr <= rxsr(2 downto 0) & rec_den;

        
                        if ((timeout_cnt = RS485_TIMEOUT) or (rxcnt = RX_BYTES))  then
                                rxcnt <= 0;
                                started <= '0';
                                rec_valid <= '1';
                                timeout_cnt <= 0;
                                rec_timeout_occured <= '0';
                                if (timeout_cnt = RS485_TIMEOUT) then
                                        rec_timeout_occured <= '1';
                                end if;
                        else
                                -- since neither the timeout counter is overrun, 
                                        -- it should be increased if 'started'
                                if (started = '1') then
                                        timeout_cnt <= timeout_cnt + 1;
                                end if;
                                
                                -- nor the message, was completely received.
                                        -- maybe we have to receive a bit now --> 
                                if (rxsr(3 downto 2) = "01") then -- identify rising edge of rec_den
                                        started <= '1';
                                        rec_dout((rxcnt*rec_din'length + rec_din'length - 1) downto (rxcnt*rec_din'length)) <= rec_din;
                                        rxcnt <= rxcnt + 1;
                                        if (rxcnt < RX_BYTES - 1) then
                                                rec_valid <= '0';
                                                rec_timeout_occured <= '0';
                                        end if;
                                end if;
                        
                        end if;
                        
                        if (start_sr = "01") then
                                started <= '1';
                                rec_valid <= '0';
                                rec_dout <= (others => '0');
                        end if;

        
                end if; --rising edge
        end process;
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        

END ARCHITECTURE beha;