| 1 | #ifndef __AD7719_ADC_H
|
|---|
| 2 | #define __AD7719_ADC_H
|
|---|
| 3 | //-----------------------------------------------------------------------------
|
|---|
| 4 |
|
|---|
| 5 | #include "typedefs.h"
|
|---|
| 6 | #include "application.h"
|
|---|
| 7 | #include "num_conversion.h"
|
|---|
| 8 | //-----------------------------------------------------------------------------
|
|---|
| 9 | // Bit Definitions
|
|---|
| 10 | #define ADC_RDY PD6
|
|---|
| 11 | #define ADC_RST PD7
|
|---|
| 12 | #define AD7719_IS_READY() (!(PIND & (1<<PD6))) // TRUE if PD6=0 AD_RDY is inverted logic.
|
|---|
| 13 |
|
|---|
| 14 | // Port Definitions
|
|---|
| 15 | #define ADC_PRT PORTD
|
|---|
| 16 | #define ADC_DDR DDRD
|
|---|
| 17 | #define ADC_PIN PIND
|
|---|
| 18 |
|
|---|
| 19 |
|
|---|
| 20 | // ON CHIP REGISTER ADDRESSES
|
|---|
| 21 | #define STATUS_RD 0x40
|
|---|
| 22 |
|
|---|
| 23 | #define MODE_WR 0x01
|
|---|
| 24 | #define MODE_RD 0x41
|
|---|
| 25 |
|
|---|
| 26 | #define AD0CON_WR 0x02
|
|---|
| 27 | #define AD0CON_RD 0x42
|
|---|
| 28 |
|
|---|
| 29 | #define AD1CON_WR 0x03
|
|---|
| 30 | #define AD1CON_RD 0x43
|
|---|
| 31 |
|
|---|
| 32 | #define FILTER_WR 0x04
|
|---|
| 33 | #define FILTER_RD 0x44
|
|---|
| 34 |
|
|---|
| 35 | #define AD0DAT_RD 0x45
|
|---|
| 36 | #define AD1DAT_RD 0x46
|
|---|
| 37 |
|
|---|
| 38 | #define IOCON_WR 0x07
|
|---|
| 39 | #define IOCON_RD 0x47
|
|---|
| 40 |
|
|---|
| 41 | #define AD0OFS_WR 0x08
|
|---|
| 42 | #define AD0OFS_RD 0x48
|
|---|
| 43 |
|
|---|
| 44 | #define AD1OFS_WR 0x09
|
|---|
| 45 | #define AD1OFS_RD 0x49
|
|---|
| 46 |
|
|---|
| 47 | #define AD0GAIN_WR 0x0A
|
|---|
| 48 | #define AD0GAIN_RD 0x4A
|
|---|
| 49 |
|
|---|
| 50 | #define AD1GAIN_WR 0x0B
|
|---|
| 51 | #define AD1GAIN_RD 0x4B
|
|---|
| 52 |
|
|---|
| 53 | #define ID_RD 0x4F
|
|---|
| 54 |
|
|---|
| 55 | // REGISTER INIT VALUES
|
|---|
| 56 |
|
|---|
| 57 | //Init Configure and Initialize AD7719
|
|---|
| 58 | //http://designtools.analog.com/dt/adc/codegen/ad7719.html
|
|---|
| 59 |
|
|---|
| 60 | #define IOCON_INIT_HIGH 0x03 //0000.0011 // I-sources I1 and I2 are switched on, thats all
|
|---|
| 61 | #define IOCON_INIT_LOWBYTE 0x00
|
|---|
| 62 |
|
|---|
| 63 | #define FILTER_INIT 0x52 //0x52 euro use 50Hz = -171dB and 60Hz = -58dB Rejectjon Updaterate = 4Hz
|
|---|
| 64 | // 0x52=82 decimal. f_ADC=16.6Hz; t_ADC=60ms; t_settle = 120ms
|
|---|
| 65 |
|
|---|
| 66 | #define AD1CON_INIT 0x31 //0011.0001
|
|---|
| 67 | // AD1EN is set --> AUX ADc is used for Temp measurement.
|
|---|
| 68 | // ACH = 011 --> Tempsensor
|
|---|
| 69 | // U/#B = 0 --> bipolar, but i'm not entirely sure if this is correct.
|
|---|
| 70 | // ARN = 1 --> input range is REFIN2 , but when tempsensor is chosen, internal ref is used ...
|
|---|
| 71 |
|
|---|
| 72 | #define AD0CON_INIT 0x8E // 1000.1110
|
|---|
| 73 | // AD0EN is set
|
|---|
| 74 | // WL is cleared --> 24bit
|
|---|
| 75 | // CH = 00 --> AIN1 , AIN2 used
|
|---|
| 76 | // U/#B = 1 --> unipolar
|
|---|
| 77 | // RN=110 --> input range = +-1.28V --> whatever this means in ratiometric measurements.
|
|---|
| 78 |
|
|---|
| 79 |
|
|---|
| 80 | #define MODE_IDLE 0x01
|
|---|
| 81 | #define MODE_SINGLE 0x02
|
|---|
| 82 | #define MODE_CONT 0x03
|
|---|
| 83 | #define MODE_INTERNAL_ZERO_CAL 0x04 // not tested
|
|---|
| 84 | #define MODE_INTERNAL_FULL_CAL 0x05 // not tested
|
|---|
| 85 |
|
|---|
| 86 | // since the ADC is chopped, one should wait 3 conversions
|
|---|
| 87 | // after the muxer was switched, until the reading is okay.
|
|---|
| 88 | #define READINGS_UNTIL_AD7719_SETTLED 3
|
|---|
| 89 |
|
|---|
| 90 | void ad7719_init(void);
|
|---|
| 91 | void startconv(U08 continuous);
|
|---|
| 92 | void stopconv(void);
|
|---|
| 93 | U32 read_adc(void);
|
|---|
| 94 | //-----------------------------------------------------------------------------
|
|---|
| 95 | #endif
|
|---|
