#ifndef __W5100_SPI_INTERFACE_H #define __W5100_SPI_INTERFACE_H //----------------------------------------------------------------------------- #include "typedefs.h" #include "application.h" //#include "num_conversion.h" extern volatile BOOL sock0_connection_established; #define ETH_READ_BUFFER_SIZE 4 #define ETH_WRITE_BUFFER_SIZE 32 extern volatile U08 eth_read_buffer[ETH_READ_BUFFER_SIZE]; extern volatile U08 eth_write_buffer[ETH_WRITE_BUFFER_SIZE]; extern U08 eth_write_index; //----------------------------------------------------------------------------- // Port Definitions // Pin Definitions // W5100 is SPI device 0 // -- so there is no need to define special pins. // -- refer to the device by using the global buffers: // volatile U08 spi_read_buffer[SPI_READ_BUFFER_SIZE]; // volatile U08 spi_write_buffer[SPI_WRITE_BUFFER_SIZE]; // // and the spi function: // void spi_transfer(U08 bytes, U08 device) // // when only sending one byte, you can do: // U08 returnvalue; // CLR_BIT(SPI_DEVICE_SS_PRT[0], SPI_DEVICE_SS[0]); // Set CS low // returnvalue = spi_transfer_byte(0xFF); // SET_BIT(SPI_DEVICE_SS_PRT[0], SPI_DEVICE_SS[0]); // Set CS high // // W5100 supports SPI modes 0 and 3 --> cpol/cpha= 0/0 or 1/1 // we only use socket 0 in this application. So only a few of W5100 adresses are mentioned here // W5100 MEM Addresses // Common registers: #define CM_MR 0x0000 // mode register #define CM_GAR0 0x0001 // Gateway adress #define CM_GAR1 0x0002 // Gateway adress #define CM_GAR2 0x0003 // Gateway adress #define CM_GAR3 0x0004 // Gateway adress #define CM_SUBR0 0x0005 // Subnetmask adress #define CM_SUBR1 0x0006 // Subnetmask adress #define CM_SUBR2 0x0007 // Subnetmask adress #define CM_SUBR3 0x0008 // Subnetmask adress #define CM_SHAR0 0x0009 // Source Hardware adress: MAC #define CM_SHAR1 0x000A // Source Hardware adress: MAC #define CM_SHAR2 0x000B // Source Hardware adress: MAC #define CM_SHAR3 0x000C // Source Hardware adress: MAC #define CM_SHAR4 0x000D // Source Hardware adress: MAC #define CM_SHAR5 0x000E // Source Hardware adress: MAC #define CM_SIPR0 0x000F // Source IP adress #define CM_SIPR1 0x0010 // Source IP adress #define CM_SIPR2 0x0011 // Source IP adress #define CM_SIPR3 0x0012 // Source IP adress #define CM_IR 0x0015 // Interrupt #define CM_IMR 0x0016 // Source IP adress #define CM_RTR0 0x0017 // retry time register #define CM_RTR1 0x0018 // retry time register #define CM_RCR 0x0019 // Retry count #define CM_RMSR 0x001A // RX mem size -- full mem size for sock0 --> value=0x03 #define CM_TMSR 0x001B // TX mem size -- full mem size for sock0 --> value=0x03 // Socket 0 registers #define S0_MR 0x0400 // Socket 0 mode -- for TCP value = 0x01 (set bit 5 for no delay ACK) #define S0_CR 0x0401 // socket 0 command -- for commands see below #define S0_IR 0x0402 // socket 0 interrupt -- see bit description below #define S0_SR 0x0403 // socket 0 status -- see below #define S0_PORT0 0x0404 // socket 0 Port MSB -- FSC might get port number 0x1F5C = 8028, since we have only one FSC in cam #define S0_PORT1 0x0405 // socket 0 Port LSB -- 0xF5C1= 62913 is okay as well ... #define S0_MSSR0 0x0412 // max segment size -- #define S0_MSSR1 0x0413 // max segment size -- reset value is 0xFFFF; is set to other party value, if in TCP passive mode #define S0_TX_FSR0 0x0420 // socket 0 TX free size #define S0_TX_FSR1 0x0421 // socket 0 TX free size #define S0_TX_RD0 0x0422 // socket 0 TX read pointer -- read only: #define S0_TX_RD1 0x0423 // socket 0 TX read pointer #define S0_TX_WR0 0x0424 // socket 0 TX write pointer #define S0_TX_WR1 0x0425 // socket 0 TX write pointer #define S0_RX_RSR0 0x0426 // socket 0 RX received size #define S0_RX_RSR1 0x0427 // socket 0 RX received size #define S0_RX_RD0 0x0428 // socket 0 RX read pointer #define S0_RX_RD1 0x0429 // socket 0 RX read pointer // some register values: #define MR_TCP 0 #define MR_NOACKDELAY 5 #define CR_OPEN 0x01 #define CR_LISTEN 0x02 #define CR_CONECT 0x04 #define CR_DISCON 0x08 #define CR_CLOSE 0x10 #define CR_SEND 0x20 #define CR_RECV 0x40 #define CR_SEND_MAC 0x21 #define CR_SEND_KEEP 0x22 #define IR_SEND_OK 4 #define IR_TIMEOUT 3 #define IR_RECV 2 #define IR_DISCON 1 #define IR_CON 0 #define SR_SOCK_CLOSED 0x00 #define SR_SOCK_INIT 0x13 #define SR_SOCK_LISTEN 0x14 #define SR_SOCK_ESTABLISHED 0x17 #define SR_SOCK_CLOSE_WAIT 0x1C #define SR_SOCK_UDP 0x22 #define SR_SOCK_IPRAW 0x32 #define SR_SOCK_MACRAW 0x42 #define SR_SOCK_PPPOE 0x5F //changing #define SR_SOCK_SYNSENT 0x15 #define SR_SOCK_SYNRECV 0x16 #define SR_SOCK_FIN_WAIT 0x18 #define SR_SOCK_CLOSING 0x1A #define SR_SOCK_TIME_WAIT 0x1B #define SR_SOCK_LAST_ACK 0x1D #define SR_SOCK_ARP0 0x11 #define SR_SOCK_ARP1 0x21 #define SR_SOCK_ARP2 0x31 // low level functions void w5100_write( U16 addr, U08 data); U08 w5100_read( U16 addr); //------------------------------------------------------------------------------ // Description of w5100_init() function: //------------------------------------------------------------------------------ //------------------------------------------------------------------------------ // BASIC SETTINGS: //------------------------------------------------------------------------------ // leave common MR in default state: 0x00 // leave IMR in default state: 0x00 no interrupt will occur, since #INT line is not routed // leave RTR in default state: 0x07D0 --> 200ms // leave RCR in default state: 0x08, after 8 re-transmissionsm, the TIMEOUT bit in Sn_IR is set '1' //------------------------------------------------------------------------------ // NETWORK SETTING: // set GAR to FSC_GATEWAY_ADDRESS //#define FSC_GATEWAY_ADDRESS0 192 // 192.33.96.1 //#define FSC_GATEWAY_ADDRESS1 33 //#define FSC_GATEWAY_ADDRESS2 96 //#define FSC_GATEWAY_ADDRESS3 1 #define FSC_GATEWAY_ADDRESS0 10 #define FSC_GATEWAY_ADDRESS1 0 #define FSC_GATEWAY_ADDRESS2 0 #define FSC_GATEWAY_ADDRESS3 0 //#define FSC_GATEWAY_ADDRESS0 192 // 192.168.0.1 //#define FSC_GATEWAY_ADDRESS1 168 //#define FSC_GATEWAY_ADDRESS2 0 //#define FSC_GATEWAY_ADDRESS3 1 // set SHAR to FSC_MAC_ADDRESS #define FSC_MAC_ADDRESS0 0xFA //FA:C7:0F:AD:22:01 #define FSC_MAC_ADDRESS1 0xC7 #define FSC_MAC_ADDRESS2 0x0F #define FSC_MAC_ADDRESS3 0xAD #define FSC_MAC_ADDRESS4 0x22 #define FSC_MAC_ADDRESS5 0x01 // set SUBR to FSC_SUBNET_MASK #define FSC_SUBNET_MASK0 255 //255.255.255.0 #define FSC_SUBNET_MASK1 255 #define FSC_SUBNET_MASK2 255 #define FSC_SUBNET_MASK3 0 // set SIPR to FSC_IP_ADDRESS //#define FSC_IP_ADDRESS0 192 // 192.33.99.247 //#define FSC_IP_ADDRESS1 33 //#define FSC_IP_ADDRESS2 99 //#define FSC_IP_ADDRESS3 247 #define FSC_IP_ADDRESS0 10 #define FSC_IP_ADDRESS1 0 #define FSC_IP_ADDRESS2 128 #define FSC_IP_ADDRESS3 127 //#define FSC_IP_ADDRESS0 192 // 192.168.0.2 //#define FSC_IP_ADDRESS1 168 //#define FSC_IP_ADDRESS2 0 //#define FSC_IP_ADDRESS3 2 //------------------------------------------------------------------------------ // MEM SETTINGS: // we plan the possible use of 2 Sockets: // Socket 0 for command input and requested data output // Socket 1 as a Webserver // // set RMSR=0x0A --> 4k memory for Socket 0 and 1 #define RX_MEM_BASE 0x6000 #define S0_RX_BASE 0x6000 // since it is the first socket its base adress is just the RX MEM SPACE BASE #define S0_RX_MASK 0x0FFF // this is 4k - 1 #define S1_RX_BASE 0x7000 // 2nd socket start, right after first socket #define S1_RX_MASK 0x0FFF // again: 4k - 1 // set TMSR=0x0A --> 4k mem for each socket #define TX_MEM_BASE 0x4000 #define S0_TX_BASE 0x4000 // since it is the first socket its base adress is just the RX MEM SPACE BASE #define S0_TX_MASK 0x0FFF // this is 4k - 1 #define S1_TX_BASE 0x5000 // 2nd socket start, right after first socket #define S1_TX_MASK 0x0FFF // again: 4k - 1 //------------------------------------------------------------------------------ U08 w5100_init(); // -- returns: TRUE if socket status is == SR_SOCK_ESTABLISHED BOOL w5100_is_established(); // request socket status info: U08 w5100_sock_status(); U16 w5100_get_received_size(); U16 w5100_get_start_address(); //----------------------------------------------------------------------------- #endif //__W5100_SPI_INTERFACE_H U16 get_S0_TX_FSR(); U16 get_S0_TX_RD(); U16 get_S0_TX_WR(); U16 get_S0_RX_RSR(); U16 get_S0_RX_RD(); U08 w5100_get_RX(U08 NumBytes, BOOL send_ACK); void w5100_TX(U08 NumBytes, U08 *str); U16 w5100_set_TX(volatile U08* string, U16 NumBytes); extern bool w5100_needs_init; extern bool w5100_ready; U08 w5100_caretaker(); void w5100_reset() ; void eth_write_str( U08* str ); void eth_writeln_str( U08* str ); void eth_write_lf(void);