| 1 | #ifndef __W5100_SPI_INTERFACE_H
|
|---|
| 2 | #define __W5100_SPI_INTERFACE_H
|
|---|
| 3 | //-----------------------------------------------------------------------------
|
|---|
| 4 |
|
|---|
| 5 | #include "typedefs.h"
|
|---|
| 6 | #include "application.h"
|
|---|
| 7 | #include "num_conversion.h"
|
|---|
| 8 |
|
|---|
| 9 | extern volatile BOOL sock0_connection_established;
|
|---|
| 10 |
|
|---|
| 11 |
|
|---|
| 12 | #define ETH_READ_BUFFER_SIZE 4
|
|---|
| 13 | #define ETH_WRITE_BUFFER_SIZE 32
|
|---|
| 14 | extern volatile U08 eth_read_buffer[ETH_READ_BUFFER_SIZE];
|
|---|
| 15 | extern volatile U08 eth_write_buffer[ETH_WRITE_BUFFER_SIZE];
|
|---|
| 16 | extern U08 eth_write_index;
|
|---|
| 17 | //-----------------------------------------------------------------------------
|
|---|
| 18 | // Port Definitions
|
|---|
| 19 | // Pin Definitions
|
|---|
| 20 | // W5100 is SPI device 0
|
|---|
| 21 | // -- so there is no need to define special pins.
|
|---|
| 22 | // -- refer to the device by using the global buffers:
|
|---|
| 23 | // volatile U08 spi_read_buffer[SPI_READ_BUFFER_SIZE];
|
|---|
| 24 | // volatile U08 spi_write_buffer[SPI_WRITE_BUFFER_SIZE];
|
|---|
| 25 | //
|
|---|
| 26 | // and the spi function:
|
|---|
| 27 | // void spi_transfer(U08 bytes, U08 device)
|
|---|
| 28 | //
|
|---|
| 29 | // when only sending one byte, you can do:
|
|---|
| 30 | // U08 returnvalue;
|
|---|
| 31 | // CLR_BIT(SPI_DEVICE_SS_PRT[0], SPI_DEVICE_SS[0]); // Set CS low
|
|---|
| 32 | // returnvalue = spi_transfer_byte(0xFF);
|
|---|
| 33 | // SET_BIT(SPI_DEVICE_SS_PRT[0], SPI_DEVICE_SS[0]); // Set CS high
|
|---|
| 34 | //
|
|---|
| 35 | // W5100 supports SPI modes 0 and 3 --> cpol/cpha= 0/0 or 1/1
|
|---|
| 36 |
|
|---|
| 37 | // we only use socket 0 in this application. So only a few of W5100 adresses are mentioned here
|
|---|
| 38 | // W5100 MEM Addresses
|
|---|
| 39 | // Common registers:
|
|---|
| 40 | #define CM_MR 0x0000 // mode register
|
|---|
| 41 | #define CM_GAR0 0x0001 // Gateway adress
|
|---|
| 42 | #define CM_GAR1 0x0002 // Gateway adress
|
|---|
| 43 | #define CM_GAR2 0x0003 // Gateway adress
|
|---|
| 44 | #define CM_GAR3 0x0004 // Gateway adress
|
|---|
| 45 | #define CM_SUBR0 0x0005 // Subnetmask adress
|
|---|
| 46 | #define CM_SUBR1 0x0006 // Subnetmask adress
|
|---|
| 47 | #define CM_SUBR2 0x0007 // Subnetmask adress
|
|---|
| 48 | #define CM_SUBR3 0x0008 // Subnetmask adress
|
|---|
| 49 | #define CM_SHAR0 0x0009 // Source Hardware adress: MAC
|
|---|
| 50 | #define CM_SHAR1 0x000A // Source Hardware adress: MAC
|
|---|
| 51 | #define CM_SHAR2 0x000B // Source Hardware adress: MAC
|
|---|
| 52 | #define CM_SHAR3 0x000C // Source Hardware adress: MAC
|
|---|
| 53 | #define CM_SHAR4 0x000D // Source Hardware adress: MAC
|
|---|
| 54 | #define CM_SHAR5 0x000E // Source Hardware adress: MAC
|
|---|
| 55 | #define CM_SIPR0 0x000F // Source IP adress
|
|---|
| 56 | #define CM_SIPR1 0x0010 // Source IP adress
|
|---|
| 57 | #define CM_SIPR2 0x0011 // Source IP adress
|
|---|
| 58 | #define CM_SIPR3 0x0012 // Source IP adress
|
|---|
| 59 | #define CM_IR 0x0015 // Interrupt
|
|---|
| 60 | #define CM_IMR 0x0016 // Source IP adress
|
|---|
| 61 | #define CM_RTR0 0x0017 // retry time register
|
|---|
| 62 | #define CM_RTR1 0x0018 // retry time register
|
|---|
| 63 | #define CM_RCR 0x0019 // Retry count
|
|---|
| 64 | #define CM_RMSR 0x001A // RX mem size -- full mem size for sock0 --> value=0x03
|
|---|
| 65 | #define CM_TMSR 0x001B // TX mem size -- full mem size for sock0 --> value=0x03
|
|---|
| 66 |
|
|---|
| 67 | // Socket 0 registers
|
|---|
| 68 | #define S0_MR 0x0400 // Socket 0 mode -- for TCP value = 0x01 (set bit 5 for no delay ACK)
|
|---|
| 69 | #define S0_CR 0x0401 // socket 0 command -- for commands see below
|
|---|
| 70 | #define S0_IR 0x0402 // socket 0 interrupt -- see bit description below
|
|---|
| 71 | #define S0_SR 0x0403 // socket 0 status -- see below
|
|---|
| 72 | #define S0_PORT0 0x0404 // socket 0 Port MSB -- FSC might get port number 0x1F5C = 8028, since we have only one FSC in cam
|
|---|
| 73 | #define S0_PORT1 0x0405 // socket 0 Port LSB -- 0xF5C1= 62913 is okay as well ...
|
|---|
| 74 | #define S0_MSSR0 0x0412 // max segment size --
|
|---|
| 75 | #define S0_MSSR1 0x0413 // max segment size -- reset value is 0xFFFF; is set to other party value, if in TCP passive mode
|
|---|
| 76 | #define S0_TX_FSR0 0x0420 // socket 0 TX free size
|
|---|
| 77 | #define S0_TX_FSR1 0x0421 // socket 0 TX free size
|
|---|
| 78 | #define S0_TX_RD0 0x0422 // socket 0 TX read pointer -- read only:
|
|---|
| 79 | #define S0_TX_RD1 0x0423 // socket 0 TX read pointer
|
|---|
| 80 | #define S0_TX_WR0 0x0424 // socket 0 TX write pointer
|
|---|
| 81 | #define S0_TX_WR1 0x0425 // socket 0 TX write pointer
|
|---|
| 82 | #define S0_RX_RSR0 0x0426 // socket 0 RX received size
|
|---|
| 83 | #define S0_RX_RSR1 0x0427 // socket 0 RX received size
|
|---|
| 84 | #define S0_RX_RD0 0x0428 // socket 0 RX read pointer
|
|---|
| 85 | #define S0_RX_RD1 0x0429 // socket 0 RX read pointer
|
|---|
| 86 |
|
|---|
| 87 |
|
|---|
| 88 |
|
|---|
| 89 | // some register values:
|
|---|
| 90 | #define MR_TCP 0
|
|---|
| 91 | #define MR_NOACKDELAY 5
|
|---|
| 92 |
|
|---|
| 93 | #define CR_OPEN 0x01
|
|---|
| 94 | #define CR_LISTEN 0x02
|
|---|
| 95 | #define CR_CONECT 0x04
|
|---|
| 96 | #define CR_DISCON 0x08
|
|---|
| 97 | #define CR_CLOSE 0x10
|
|---|
| 98 | #define CR_SEND 0x20
|
|---|
| 99 | #define CR_RECV 0x40
|
|---|
| 100 | #define CR_SEND_MAC 0x21
|
|---|
| 101 | #define CR_SEND_KEEP 0x22
|
|---|
| 102 |
|
|---|
| 103 | #define IR_SEND_OK 4
|
|---|
| 104 | #define IR_TIMEOUT 3
|
|---|
| 105 | #define IR_RECV 2
|
|---|
| 106 | #define IR_DISCON 1
|
|---|
| 107 | #define IR_CON 0
|
|---|
| 108 |
|
|---|
| 109 | #define SR_SOCK_CLOSED 0x00
|
|---|
| 110 | #define SR_SOCK_INIT 0x13
|
|---|
| 111 | #define SR_SOCK_LISTEN 0x14
|
|---|
| 112 | #define SR_SOCK_ESTABLISHED 0x17
|
|---|
| 113 | #define SR_SOCK_CLOSE_WAIT 0x1C
|
|---|
| 114 | #define SR_SOCK_UDP 0x22
|
|---|
| 115 | #define SR_SOCK_IPRAW 0x32
|
|---|
| 116 | #define SR_SOCK_MACRAW 0x42
|
|---|
| 117 | #define SR_SOCK_PPPOE 0x5F
|
|---|
| 118 | //changing
|
|---|
| 119 | #define SR_SOCK_SYNSENT 0x15
|
|---|
| 120 | #define SR_SOCK_SYNRECV 0x16
|
|---|
| 121 | #define SR_SOCK_FIN_WAIT 0x18
|
|---|
| 122 | #define SR_SOCK_CLOSING 0x1A
|
|---|
| 123 | #define SR_SOCK_TIME_WAIT 0x1B
|
|---|
| 124 | #define SR_SOCK_LAST_ACK 0x1D
|
|---|
| 125 | #define SR_SOCK_ARP0 0x11
|
|---|
| 126 | #define SR_SOCK_ARP1 0x21
|
|---|
| 127 | #define SR_SOCK_ARP2 0x31
|
|---|
| 128 |
|
|---|
| 129 | // low level functions
|
|---|
| 130 | void w5100_write( U16 addr, U08 data);
|
|---|
| 131 | U08 w5100_read( U16 addr);
|
|---|
| 132 |
|
|---|
| 133 | //------------------------------------------------------------------------------
|
|---|
| 134 | // Description of w5100_init() function:
|
|---|
| 135 | //------------------------------------------------------------------------------
|
|---|
| 136 | //------------------------------------------------------------------------------
|
|---|
| 137 | // BASIC SETTINGS:
|
|---|
| 138 | //------------------------------------------------------------------------------
|
|---|
| 139 | // leave common MR in default state: 0x00
|
|---|
| 140 | // leave IMR in default state: 0x00 no interrupt will occur, since #INT line is not routed
|
|---|
| 141 | // leave RTR in default state: 0x07D0 --> 200ms
|
|---|
| 142 | // leave RCR in default state: 0x08, after 8 re-transmissionsm, the TIMEOUT bit in Sn_IR is set '1'
|
|---|
| 143 | //------------------------------------------------------------------------------
|
|---|
| 144 | // NETWORK SETTING:
|
|---|
| 145 | // set GAR to FSC_GATEWAY_ADDRESS
|
|---|
| 146 | //#define FSC_GATEWAY_ADDRESS0 192 // 192.33.96.1
|
|---|
| 147 | //#define FSC_GATEWAY_ADDRESS1 33
|
|---|
| 148 | //#define FSC_GATEWAY_ADDRESS2 96
|
|---|
| 149 | //#define FSC_GATEWAY_ADDRESS3 1
|
|---|
| 150 |
|
|---|
| 151 | #define FSC_GATEWAY_ADDRESS0 10
|
|---|
| 152 | #define FSC_GATEWAY_ADDRESS1 0
|
|---|
| 153 | #define FSC_GATEWAY_ADDRESS2 0
|
|---|
| 154 | #define FSC_GATEWAY_ADDRESS3 0
|
|---|
| 155 |
|
|---|
| 156 |
|
|---|
| 157 | //#define FSC_GATEWAY_ADDRESS0 192 // 192.168.0.1
|
|---|
| 158 | //#define FSC_GATEWAY_ADDRESS1 168
|
|---|
| 159 | //#define FSC_GATEWAY_ADDRESS2 0
|
|---|
| 160 | //#define FSC_GATEWAY_ADDRESS3 1
|
|---|
| 161 |
|
|---|
| 162 |
|
|---|
| 163 | // set SHAR to FSC_MAC_ADDRESS
|
|---|
| 164 | #define FSC_MAC_ADDRESS0 0xFA //FA:C7:0F:AD:22:01
|
|---|
| 165 | #define FSC_MAC_ADDRESS1 0xC7
|
|---|
| 166 | #define FSC_MAC_ADDRESS2 0x0F
|
|---|
| 167 | #define FSC_MAC_ADDRESS3 0xAD
|
|---|
| 168 | #define FSC_MAC_ADDRESS4 0x22
|
|---|
| 169 | #define FSC_MAC_ADDRESS5 0x01
|
|---|
| 170 |
|
|---|
| 171 | // set SUBR to FSC_SUBNET_MASK
|
|---|
| 172 | #define FSC_SUBNET_MASK0 255 //255.255.255.0
|
|---|
| 173 | #define FSC_SUBNET_MASK1 255
|
|---|
| 174 | #define FSC_SUBNET_MASK2 255
|
|---|
| 175 | #define FSC_SUBNET_MASK3 0
|
|---|
| 176 | // set SIPR to FSC_IP_ADDRESS
|
|---|
| 177 |
|
|---|
| 178 | //#define FSC_IP_ADDRESS0 192 // 192.33.99.247
|
|---|
| 179 | //#define FSC_IP_ADDRESS1 33
|
|---|
| 180 | //#define FSC_IP_ADDRESS2 99
|
|---|
| 181 | //#define FSC_IP_ADDRESS3 247
|
|---|
| 182 |
|
|---|
| 183 | #define FSC_IP_ADDRESS0 10
|
|---|
| 184 | #define FSC_IP_ADDRESS1 0
|
|---|
| 185 | #define FSC_IP_ADDRESS2 128
|
|---|
| 186 | #define FSC_IP_ADDRESS3 127
|
|---|
| 187 |
|
|---|
| 188 |
|
|---|
| 189 | //#define FSC_IP_ADDRESS0 192 // 192.168.0.2
|
|---|
| 190 | //#define FSC_IP_ADDRESS1 168
|
|---|
| 191 | //#define FSC_IP_ADDRESS2 0
|
|---|
| 192 | //#define FSC_IP_ADDRESS3 2
|
|---|
| 193 |
|
|---|
| 194 |
|
|---|
| 195 | //------------------------------------------------------------------------------
|
|---|
| 196 | // MEM SETTINGS:
|
|---|
| 197 | // we plan the possible use of 2 Sockets:
|
|---|
| 198 | // Socket 0 for command input and requested data output
|
|---|
| 199 | // Socket 1 as a Webserver
|
|---|
| 200 | //
|
|---|
| 201 | // set RMSR=0x0A --> 4k memory for Socket 0 and 1
|
|---|
| 202 | #define RX_MEM_BASE 0x6000
|
|---|
| 203 | #define S0_RX_BASE 0x6000 // since it is the first socket its base adress is just the RX MEM SPACE BASE
|
|---|
| 204 | #define S0_RX_MASK 0x0FFF // this is 4k - 1
|
|---|
| 205 | #define S1_RX_BASE 0x7000 // 2nd socket start, right after first socket
|
|---|
| 206 | #define S1_RX_MASK 0x0FFF // again: 4k - 1
|
|---|
| 207 | // set TMSR=0x0A --> 4k mem for each socket
|
|---|
| 208 | #define TX_MEM_BASE 0x4000
|
|---|
| 209 | #define S0_TX_BASE 0x4000 // since it is the first socket its base adress is just the RX MEM SPACE BASE
|
|---|
| 210 | #define S0_TX_MASK 0x0FFF // this is 4k - 1
|
|---|
| 211 | #define S1_TX_BASE 0x5000 // 2nd socket start, right after first socket
|
|---|
| 212 | #define S1_TX_MASK 0x0FFF // again: 4k - 1
|
|---|
| 213 | //------------------------------------------------------------------------------
|
|---|
| 214 | U08 w5100_init();
|
|---|
| 215 |
|
|---|
| 216 |
|
|---|
| 217 | // -- returns: TRUE if socket status is == SR_SOCK_ESTABLISHED
|
|---|
| 218 | BOOL w5100_is_established();
|
|---|
| 219 | // request socket status info:
|
|---|
| 220 | U08 w5100_sock_status();
|
|---|
| 221 |
|
|---|
| 222 |
|
|---|
| 223 | U16 w5100_get_received_size();
|
|---|
| 224 | U16 w5100_get_start_address();
|
|---|
| 225 | //-----------------------------------------------------------------------------
|
|---|
| 226 | #endif //__W5100_SPI_INTERFACE_H
|
|---|
| 227 |
|
|---|
| 228 | U16 get_S0_TX_FSR();
|
|---|
| 229 | U16 get_S0_TX_RD();
|
|---|
| 230 | U16 get_S0_TX_WR();
|
|---|
| 231 | U16 get_S0_RX_RSR();
|
|---|
| 232 | U16 get_S0_RX_RD();
|
|---|
| 233 | U08 w5100_get_RX(U08 NumBytes, BOOL send_ACK);
|
|---|
| 234 | void w5100_TX(U08 NumBytes, U08 *str);
|
|---|
| 235 | U16 w5100_set_TX(U08* string, U16 NumBytes);
|
|---|
| 236 |
|
|---|
| 237 | extern bool w5100_needs_init;
|
|---|
| 238 | extern bool w5100_ready;
|
|---|
| 239 |
|
|---|
| 240 |
|
|---|
| 241 |
|
|---|
| 242 | U08 w5100_caretaker();
|
|---|
| 243 | void w5100_reset() ;
|
|---|
| 244 |
|
|---|
| 245 |
|
|---|
| 246 | void eth_write_str( U08* str );
|
|---|
| 247 | void eth_writeln_str( U08* str );
|
|---|
| 248 | void eth_write_lf(void); |
|---|
