---------------------------------------------------------------------------------- -- Company: ETH Zurich, Institute for Particle Physics -- Engineer: P. Vogler, Q. Weitzel -- -- Create Date: 08 December 2010 -- Design Name: -- Module Name: FTM_top - Behavioral -- Project Name: -- Target Devices: -- Tool versions: -- Description: Top level entity for FTM firmware -- -- -- Dependencies: -- -- Revision: -- Revision 0.01 - File Created -- Additional Comments: -- ---------------------------------------------------------------------------------- library IEEE; use IEEE.STD_LOGIC_1164.ALL; use IEEE.STD_LOGIC_ARITH.ALL; use IEEE.STD_LOGIC_UNSIGNED.ALL; library ftm_definitions; USE ftm_definitions.ftm_array_types.all; USE ftm_definitions.ftm_constants.all; ---- Uncomment the following library declaration if instantiating ---- any Xilinx primitives in this code. library UNISIM; use UNISIM.VComponents.all; entity FTM_top is port( -- Clock clk : IN STD_LOGIC; -- external clock from oscillator U47 -- connection to the WIZnet W5300 ethernet controller -- on IO-Bank 1 ------------------------------------------------------------------------------- -- W5300 data bus W_D : inout STD_LOGIC_VECTOR(15 downto 0); -- 16-bit data bus to W5300 -- W5300 address bus W_A : out STD_LOGIC_VECTOR(9 downto 0); -- there is no real net W_A0 because -- the W5300 is operated in the -- 16-bit mode -- -> W_A<0> assigned to unconnected pin -- W5300 control signals -- the signals W_INT, W_RD, W_WR and W_RES also go to testpoints T17 -- W_CS is also routed to testpoint JP7 W_CS : out STD_LOGIC := '1'; -- W5300 chip select W_INT : IN STD_LOGIC; -- interrupt W_RD : out STD_LOGIC := '1'; -- read W_WR : out STD_LOGIC := '1'; -- write W_RES : out STD_LOGIC := '1'; -- reset W5300 chip -- W5300 buffer ready indicator -- W_BRDY : in STD_LOGIC_VECTOR(3 downto 0); -- testpoints (T18) associated with the W5300 on IO-bank 1 -- W_T : inout STD_LOGIC_VECTOR(3 downto 0); -- SPI Interface -- connection to the EEPROM U36 (AL25L016M) and -- temperature sensors U45, U46, U48 and U49 (all MAX6662) -- on IO-Bank 1 ------------------------------------------------------------------------------- -- S_CLK : out STD_LOGIC; -- SPI clock -- EEPROM -- MOSI : out STD_LOGIC; -- master out slave in -- MISO : in STD_LOGIC; -- master in slave out -- EE_CS : out STD_LOGIC; -- EEPROM chip select -- temperature sensors U45, U46, U48 and U49 -- SIO : inout STD_LOGIC; -- serial IO -- TS_CS : out STD_LOGIC_VECTOR(3 downto 0); -- temperature sensors chip select -- Trigger primitives inputs -- on IO-Bank 2 ------------------------------------------------------------------------------- Trig_Prim_A : in STD_LOGIC_VECTOR(9 downto 0); -- crate 0 Trig_Prim_B : in STD_LOGIC_VECTOR(9 downto 0); -- crate 1 Trig_Prim_C : in STD_LOGIC_VECTOR(9 downto 0); -- crate 2 Trig_Prim_D : in STD_LOGIC_VECTOR(9 downto 0); -- crate 3 -- NIM inputs ------------------------------------------------------------------------------ -- on IO-Bank 3 ext_Trig : in STD_LOGIC_VECTOR(2 downto 1); -- external trigger input Veto : in STD_LOGIC; -- trigger veto input -- NIM_In : in STD_LOGIC_VECTOR(2 downto 0); -- auxiliary inputs -- on IO-Bank 0 -- alternative external clock input for FPGA -- NIM_In3_GCLK : in STD_LOGIC; -- input with global clock buffer available -- LEDs on IO-Banks 0 and 3 ------------------------------------------------------------------------------- LED_red : out STD_LOGIC_VECTOR(3 downto 0); -- red LED_ye : out STD_LOGIC_VECTOR(1 downto 0); -- yellow LED_gn : out STD_LOGIC_VECTOR(1 downto 0); -- green -- Clock conditioner LMK03000 -- on IO-Bank 3 ------------------------------------------------------------------------------- CLK_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface serial clock LE_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface latch enable DATA_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface data SYNC_Clk_Cond : out STD_LOGIC; -- global clock synchronization LD_Clk_Cond : in STD_LOGIC; -- lock detect -- various RS-485 Interfaces -- on IO-Bank 3 ------------------------------------------------------------------------------- -- Bus 1: FTU slow control Bus1_Tx_En : out STD_LOGIC; -- bus 1: transmitter enable Bus1_Rx_En : out STD_LOGIC; -- bus 1: receiver enable Bus1_RxD_0 : in STD_LOGIC; -- crate 0 Bus1_TxD_0 : out STD_LOGIC; Bus1_RxD_1 : in STD_LOGIC; -- crate 1 Bus1_TxD_1 : out STD_LOGIC; Bus1_RxD_2 : in STD_LOGIC; -- crate 2 Bus1_TxD_2 : out STD_LOGIC; Bus1_RxD_3 : in STD_LOGIC; -- crate 3 Bus1_TxD_3 : out STD_LOGIC; -- Bus 2: Trigger-ID to FAD boards Bus2_Tx_En : out STD_LOGIC; -- bus 2: transmitter enable Bus2_Rx_En : out STD_LOGIC; -- bus 2: receiver enable Bus2_RxD_0 : in STD_LOGIC; -- crate 0 Bus2_TxD_0 : out STD_LOGIC; Bus2_RxD_1 : in STD_LOGIC; -- crate 1 Bus2_TxD_1 : out STD_LOGIC; Bus2_RxD_2 : in STD_LOGIC; -- crate 2 Bus2_TxD_2 : out STD_LOGIC; Bus2_RxD_3 : in STD_LOGIC; -- crate 3 Bus2_TxD_3 : out STD_LOGIC; -- auxiliary access -- Aux_Rx_D : in STD_LOGIC; -- Aux_Tx_D : out STD_LOGIC; -- Aux_Rx_En : out STD_LOGIC; -- Rx- and Tx enable -- Aux_Tx_En : out STD_LOGIC; -- also for auxiliary Trigger-ID -- auxiliary Trigger-ID (i.e. to send the Trigger-ID to the counting hut/house/container) -- TrID_Rx_D : in STD_LOGIC; -- TrID_Tx_D : out STD_LOGIC; -- Crate-Resets -- on IO-Bank 3 ------------------------------------------------------------------------------- Crate_Res0 : out STD_LOGIC; Crate_Res1 : out STD_LOGIC; Crate_Res2 : out STD_LOGIC; Crate_Res3 : out STD_LOGIC; -- Busy signals from the FAD boards -- on IO-Bank 3 ------------------------------------------------------------------------------- Busy0 : in STD_LOGIC; Busy1 : in STD_LOGIC; Busy2 : in STD_LOGIC; Busy3 : in STD_LOGIC; -- NIM outputs -- on IO-Bank 0 -- LVDS output at the FPGA followed by LVDS to NIM conversion stage ------------------------------------------------------------------------------- -- calibration -- Cal_NIM1_p : out STD_LOGIC; -- Cal_NIM1+ -- Cal_NIM1_n : out STD_LOGIC; -- Cal_NIM1- -- Cal_NIM2_p : out STD_LOGIC; -- Cal_NIM2+ -- Cal_NIM2_n : out STD_LOGIC; -- Cal_NIM2- -- auxiliarry / spare NIM outputs -- NIM_Out0_p : out STD_LOGIC; -- NIM_Out0+ -- NIM_Out0_n : out STD_LOGIC; -- NIM_Out0- -- NIM_Out1_p : out STD_LOGIC; -- NIM_Out1+ -- NIM_Out1_n : out STD_LOGIC; -- NIM_Out1- -- fast control signal outputs -- LVDS output at the FPGA followed by LVDS to NIM conversion stage ------------------------------------------------------------------------------- RES_p : out STD_LOGIC; -- RES+ Reset RES_n : out STD_LOGIC; -- RES- IO-Bank 0 TRG_p : out STD_LOGIC; -- TRG+ Trigger TRG_n : out STD_LOGIC; -- TRG- IO-Bank 0 TIM_Run_p : out STD_LOGIC; -- TIM_Run+ Time Marker TIM_Run_n : out STD_LOGIC; -- TIM_Run- IO-Bank 2 TIM_Sel : out STD_LOGIC; -- Time Marker selector on IO-Bank 2 -- CLD_FPGA : in STD_LOGIC; -- DRS-Clock feedback into FPGA -- LVDS calibration outputs -- on IO-Bank 0 ------------------------------------------------------------------------------- -- to connector J13 -- for light pulsar in the mirror dish Cal_0_p : out STD_LOGIC; Cal_0_n : out STD_LOGIC; Cal_1_p : out STD_LOGIC; Cal_1_n : out STD_LOGIC; Cal_2_p : out STD_LOGIC; Cal_2_n : out STD_LOGIC; Cal_3_p : out STD_LOGIC; Cal_3_n : out STD_LOGIC; -- to connector J12 -- for light pulsar inside shutter Cal_4_p : out STD_LOGIC; Cal_4_n : out STD_LOGIC; Cal_5_p : out STD_LOGIC; Cal_5_n : out STD_LOGIC; Cal_6_p : out STD_LOGIC; Cal_6_n : out STD_LOGIC; Cal_7_p : out STD_LOGIC; Cal_7_n : out STD_LOGIC; -- Testpoints ------------------------------------------------------------------------------- TP : inout STD_LOGIC_VECTOR(32 downto 0) -- TP_in : in STD_LOGIC_VECTOR(34 downto 33); -- input only -- Board ID - inputs -- local board-ID "solder programmable" -- all on 'input only' pins ------------------------------------------------------------------------------- -- brd_id : in STD_LOGIC_VECTOR(7 downto 0) -- input only ); end FTM_top; architecture Behavioral of FTM_top is signal cc_R0_sig : std_logic_vector(31 DOWNTO 0); signal cc_R1_sig : std_logic_vector(31 DOWNTO 0); signal cc_R11_sig : std_logic_vector(31 DOWNTO 0); signal cc_R13_sig : std_logic_vector(31 DOWNTO 0); signal cc_R14_sig : std_logic_vector(31 DOWNTO 0); signal cc_R15_sig : std_logic_vector(31 DOWNTO 0); signal cc_R8_sig : std_logic_vector(31 DOWNTO 0); signal cc_R9_sig : std_logic_vector(31 DOWNTO 0); signal coin_n_c_sig : std_logic_vector(15 DOWNTO 0); signal coin_n_p_sig : std_logic_vector(15 DOWNTO 0); signal dead_time_sig : std_logic_vector(15 DOWNTO 0); signal ftu_active_cr0_sig : std_logic_vector(15 DOWNTO 0); signal ftu_active_cr1_sig : std_logic_vector(15 DOWNTO 0); signal ftu_active_cr2_sig : std_logic_vector(15 DOWNTO 0); signal ftu_active_cr3_sig : std_logic_vector(15 DOWNTO 0); signal general_settings_sig : std_logic_vector(15 DOWNTO 0); signal lp1_amplitude_sig : std_logic_vector(15 DOWNTO 0); signal lp1_delay_sig : std_logic_vector(15 DOWNTO 0); signal lp2_amplitude_sig : std_logic_vector(15 DOWNTO 0); signal lp2_delay_sig : std_logic_vector(15 DOWNTO 0); signal lp_pt_freq_sig : std_logic_vector(15 DOWNTO 0); signal lp_pt_ratio_sig : std_logic_vector(15 DOWNTO 0); signal timemarker_delay_sig : std_logic_vector(15 DOWNTO 0); signal trigger_delay_sig : std_logic_vector(15 DOWNTO 0); signal sd_addr_ftu_sig : std_logic_vector(11 DOWNTO 0); signal sd_busy_sig : std_logic; signal sd_data_out_ftu_sig : std_logic_vector(15 DOWNTO 0) := (others => '0'); signal sd_read_ftu_sig : std_logic; signal sd_ready_sig : std_logic; signal sd_started_ftu_sig : std_logic := '0'; signal new_config_sig : std_logic := '0'; signal config_started_sig : std_logic := '0'; signal config_start_eth_sig : std_logic := '0'; signal config_started_eth_sig : std_logic := '0'; signal config_ready_eth_sig : std_logic := '0'; signal config_started_ack_sig : std_logic := '0'; signal ping_ftu_start_sig : std_logic := '0'; signal ping_ftu_started_sig : std_logic := '0'; signal ping_ftu_ready_sig : std_logic := '0'; signal config_start_ftu_sig : std_logic := '0'; signal config_started_ftu_sig : std_logic := '0'; signal config_ready_ftu_sig : std_logic := '0'; signal rates_ftu_start_sig : std_logic := '0'; signal rates_ftu_started_sig : std_logic := '0'; signal rates_ftu_ready_sig : std_logic := '0'; signal fl_busy_sig : std_logic; signal fl_ready_sig : std_logic; signal fl_write_sig : std_logic := '0'; signal fl_started_ftu_sig : std_logic := '0'; signal fl_addr_sig : std_logic_vector(11 DOWNTO 0) := (others => '0'); signal fl_data_sig : std_logic_vector(15 DOWNTO 0) := (others => '0'); signal ping_ftu_start_ftu_sig : std_logic := '0'; signal ping_ftu_started1_sig : std_logic := '0'; signal ping_ftu_ready1_sig : std_logic := '0'; signal coin_win_c_sig : std_logic_vector(15 DOWNTO 0) := (others => '0'); signal coin_win_p_sig : std_logic_vector(15 DOWNTO 0) := (others => '0'); --new or changed stuff signal dd_data_sig : std_logic_vector(15 DOWNTO 0) := (others => '0'); signal dd_addr_sig : std_logic_vector(11 DOWNTO 0) := (others => '0'); signal dd_block_start_ftu_sig : std_logic := '0'; signal dd_block_start_ack_ftu_sig : std_logic := '0'; signal dd_block_ready_ftu_sig : std_logic := '0'; signal dd_busy_sig : std_logic; signal dd_write_sig : std_logic := '0'; signal dd_started_ftu_sig : std_logic := '0'; signal dd_ready_sig : std_logic; signal dd_send_sig : std_logic := '1'; signal dd_send_ack_sig : std_logic := '1'; signal dd_send_ready_sig : std_logic := '1'; --very new stuff SIGNAL ftu_error_send_ack_sig : std_logic := '1'; SIGNAL ftu_error_send_ready_sig : std_logic := '1'; SIGNAL ftu_error_calls_sig : std_logic_vector(15 DOWNTO 0) := X"0000"; SIGNAL ftu_error_data_sig : std_logic_vector(223 DOWNTO 0) := (others => '0'); SIGNAL ftu_error_send_sig : std_logic := '0'; signal prescaling_FTU01_sig : std_logic_vector (15 DOWNTO 0); signal trigger_counter_sig : std_logic_vector (31 DOWNTO 0); signal trigger_counter_read_sig : std_logic; signal trigger_counter_valid_sig : std_logic; signal config_start_cc_sig : std_logic; -- initialized in central control signal config_started_cc_sig : std_logic := '0'; signal config_ready_cc_sig : std_logic := '0'; signal config_start_lp_sig : std_logic; -- initialized in central control signal config_started_lp_sig : std_logic; -- initialized in light pulser interface signal config_ready_lp_sig : std_logic; -- initialized in light pulser interface signal config_trigger_sig : std_logic; signal config_trigger_done_sig : std_logic; signal clk_buf_sig : std_logic; signal clk_1M_sig : STD_LOGIC; -- generated from 50M clock by divider signal clk_50M_sig : STD_LOGIC; -- generated by internal DCM signal clk_250M_sig : STD_LOGIC; -- generated by internal DCM signal clk_250M_ps_sig : STD_LOGIC; -- generated by internal DCM signal clk_ready_sig : STD_LOGIC := '0'; -- set high by FTM_clk_gen when DCMs have locked signal trigger_ID_ready_sig : std_logic; -- initialized in trigger manager signal trigger_ID_sig : std_logic_vector(55 downto 0); -- initialized in trigger manager signal trigger_ID_read_sig : std_logic; -- initialized in FTM_fad_broadcast signal trigger_active_sig : std_logic; -- initialized in trigger manager signal reset_sig : STD_LOGIC := '0'; -- initialize to 0 on power-up signal trigger_signal_sig : std_logic := '0'; signal TIM_signal_sig : std_logic := '0'; --signals for FPGA DNA identifier signal dna_sig : STD_LOGIC_VECTOR(63 downto 0); -- initialized in FTM_dna_gen signal dna_start_sig : STD_LOGIC; -- initialized in FTM_central_control signal dna_ready_sig : STD_LOGIC; -- initialized in FTM_dna_gen signal led_sig : std_logic_vector(7 downto 0) := (others => '0'); signal get_ot_counter_sig : std_logic; signal get_ot_counter_started_sig : std_logic; signal get_ot_counter_ready_sig : std_logic; signal on_time_counter_sig : std_logic_vector(47 downto 0); signal get_ts_counter_sig : std_logic; signal get_ts_counter_started_sig : std_logic; signal get_ts_counter_ready_sig : std_logic; signal timestamp_counter_sig : std_logic_vector(47 downto 0); signal crate_reset_sig : std_logic; signal crate_reset_ack_sig : std_logic; signal crate_reset_param_sig : std_logic_vector (15 DOWNTO 0); signal start_run_sig : std_logic; signal start_run_ack_sig : std_logic; signal stop_run_sig : std_logic; signal stop_run_ack_sig : std_logic; signal current_cc_state_sig : std_logic_vector (15 DOWNTO 0); signal cc_state_test_sig : std_logic_vector ( 7 downto 0); signal start_run_param_sig : std_logic_vector (15 DOWNTO 0); signal start_run_num_events_sig : std_logic_vector (31 DOWNTO 0); signal trigger_start_sig : std_logic; signal trigger_stop_sig : std_logic; signal enable_ID_sending_sig : std_logic; signal reset_timer_sig : std_logic; -- initialized in FTM_central_control signal crate_res0_sig : std_logic; -- initialized in FTM_central_control signal crate_res1_sig : std_logic; -- initialized in FTM_central_control signal crate_res2_sig : std_logic; -- initialized in FTM_central_control signal crate_res3_sig : std_logic; -- initialized in FTM_central_control signal LP1_pulse_sig : std_logic := '0'; signal LP2_pulse_sig : std_logic := '0'; signal new_config_ftu_sig : std_logic; -- initialized in ethernet_modul signal new_config_ftu_ack_sig : std_logic; -- initialized in FTM_central_control signal new_config_ftu_param_sig : std_logic_vector (15 DOWNTO 0); -- initialized in ethernet_modul signal config_single_FTU_sig : std_logic; -- initialized in FTM_central_control signal config_single_FTU_started_sig : std_logic; -- initialized in FTM_ftu_control signal config_single_FTU_done_sig : std_logic; -- initialized in FTM_ftu_control -- component FTM_clk_gen -- port( -- clk : IN STD_LOGIC; -- rst : IN STD_LOGIC; -- clk_1 : OUT STD_LOGIC; -- clk_50 : OUT STD_LOGIC; -- clk_250 : OUT STD_LOGIC; -- clk_250_ps : OUT STD_LOGIC; -- ready : OUT STD_LOGIC -- ); -- end component; component FTM_clk_gen_2 port( clk : IN STD_LOGIC; rst : IN STD_LOGIC; clk_1 : OUT STD_LOGIC; clk_50 : OUT STD_LOGIC; clk_250 : OUT STD_LOGIC; clk_250_ps : OUT STD_LOGIC; ready : OUT STD_LOGIC ); end component; component FTM_dna_gen port( clk : IN STD_LOGIC; start : IN STD_LOGIC; dna : OUT STD_LOGIC_VECTOR(63 downto 0); ready : OUT STD_LOGIC ); end component; component trigger_manager port( --clocks clk_50MHz : in std_logic; clk_250MHz : in std_logic; clk_250MHz_180 : in std_logic; --trigger primitives from FTUs trig_prim_0 : in std_logic_vector(9 downto 0); --crate 0 trig_prim_1 : in std_logic_vector(9 downto 0); --crate 1 trig_prim_2 : in std_logic_vector(9 downto 0); --crate 2 trig_prim_3 : in std_logic_vector(9 downto 0); --crate 3 --external signals ext_trig_1 : in std_logic; ext_trig_2 : in std_logic; ext_veto : in std_logic; FAD_busy_0 : in std_logic; --crate 0 FAD_busy_1 : in std_logic; --crate 1 FAD_busy_2 : in std_logic; --crate 2 FAD_busy_3 : in std_logic; --crate 3 --control signals from e.g. main control start_run : in std_logic; --enable trigger output stop_run : in std_logic; --disable trigger output new_config : in std_logic; --settings register (see FTM Firmware Specifications) general_settings : in std_logic_vector(15 downto 0); LP_and_PED_freq : in std_logic_vector(15 downto 0); LP1_LP2_PED_ratio : in std_logic_vector(15 downto 0); maj_coinc_n_phys : in std_logic_vector(15 downto 0); maj_coinc_n_calib : in std_logic_vector(15 downto 0); trigger_delay : in std_logic_vector(15 downto 0); TIM_delay : in std_logic_vector(15 downto 0); dead_time : in std_logic_vector(15 downto 0); coinc_window_phys : in std_logic_vector(15 downto 0); coinc_window_calib : in std_logic_vector(15 downto 0); active_FTU_list_0 : in std_logic_vector(15 downto 0); active_FTU_list_1 : in std_logic_vector(15 downto 0); active_FTU_list_2 : in std_logic_vector(15 downto 0); active_FTU_list_3 : in std_logic_vector(15 downto 0); --control signals or information for other entities trigger_ID_read : in std_logic; trig_cnt_copy_read : in std_logic; trigger_ID_ready : out std_logic; trigger_ID : out std_logic_vector(55 downto 0); trig_cnt_copy : out std_logic_vector(31 downto 0); --counter reading trig_cnt_copy_valid : out std_logic; --trigger counter reading is valid trigger_active : out std_logic; --phys triggers are enabled/active config_done : out std_logic; LP1_pulse : out std_logic; --send start signal to light pulser 1 LP2_pulse : out std_logic; --send start signal to light pulser 2 --trigger and time marker output signals to FADs trigger_signal : out std_logic; TIM_signal : out std_logic ); end component; component Clock_cond_interface is port( clk : IN STD_LOGIC; CLK_Clk_Cond : out STD_LOGIC; LE_Clk_Cond : out STD_LOGIC; DATA_Clk_Cond : out STD_LOGIC; SYNC_Clk_Cond : out STD_LOGIC; LD_Clk_Cond : in STD_LOGIC; TIM_Sel : out STD_LOGIC; cc_R0 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R1 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R8 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R9 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R11 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R13 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R14 : in std_logic_vector (31 downto 0) := (others => '0'); cc_R15 : in std_logic_vector (31 downto 0) := (others => '0'); start_config : in STD_LOGIC; config_started : out STD_LOGIC; config_done : out STD_LOGIC; timemarker_select: in STD_LOGIC ); end component; component FTM_central_control port( clk : IN std_logic; clk_ready : in std_logic; clk_scaler : IN std_logic; new_config : IN std_logic; config_started : OUT std_logic := '0'; config_started_ack : IN std_logic; config_start_eth : OUT std_logic := '0'; config_started_eth : IN std_logic; config_ready_eth : IN std_logic; config_start_ftu : OUT std_logic := '0'; config_started_ftu : IN std_logic; config_ready_ftu : IN std_logic; ping_ftu_start : IN std_logic; ping_ftu_started : OUT std_logic := '0'; ping_ftu_ready : OUT std_logic := '0'; ping_ftu_start_ftu : OUT std_logic := '0'; ping_ftu_started_ftu : IN std_logic; ping_ftu_ready_ftu : IN std_logic; rates_ftu : OUT std_logic := '0'; rates_started_ftu : IN std_logic; rates_ready_ftu : IN std_logic; prescaling_FTU01 : IN std_logic_vector(7 downto 0); dd_send : OUT std_logic := '0'; dd_send_ack : IN std_logic; dd_send_ready : IN std_logic; dd_block_ready_ftu : out std_logic := '0'; dd_block_start_ack_ftu : in std_logic; dd_block_start_ftu : out std_logic := '0'; config_start_cc : out std_logic := '0'; config_started_cc : in std_logic; config_ready_cc : in std_logic; config_start_lp : out std_logic := '0'; config_started_lp : in std_logic; config_ready_lp : in std_logic; config_trigger : out std_logic; config_trigger_done : in std_logic; dna_start : out std_logic; dna_ready : in std_logic; crate_reset : IN std_logic; crate_reset_ack : OUT std_logic; crate_reset_param : IN std_logic_vector (15 DOWNTO 0); start_run : IN std_logic; start_run_ack : OUT std_logic; stop_run : IN std_logic; stop_run_ack : OUT std_logic; current_cc_state : OUT std_logic_vector (15 DOWNTO 0); cc_state_test : OUT std_logic_vector ( 7 downto 0); start_run_param : IN std_logic_vector (15 DOWNTO 0); start_run_num_events : IN std_logic_vector (31 DOWNTO 0); trigger_start : out std_logic; trigger_stop : out std_logic; enable_ID_sending : out std_logic; reset_timer : out std_logic; crate_res_0 : out std_logic; crate_res_1 : out std_logic; crate_res_2 : out std_logic; crate_res_3 : out std_logic; new_config_ftu : in std_logic; new_config_ftu_ack : out std_logic := '0'; config_single_FTU : out std_logic := '0'; config_single_FTU_started : in std_logic; config_single_FTU_done : in std_logic ); end component; component FTM_ftu_control port( clk_50MHz : in std_logic; rx_en : out STD_LOGIC; tx_en : out STD_LOGIC; rx_d_0 : in STD_LOGIC; tx_d_0 : out STD_LOGIC; rx_d_1 : in STD_LOGIC; tx_d_1 : out STD_LOGIC; rx_d_2 : in STD_LOGIC; tx_d_2 : out STD_LOGIC; rx_d_3 : in STD_LOGIC; tx_d_3 : out STD_LOGIC; new_config : in std_logic; ping_all : in std_logic; read_rates : in std_logic; config_single_FTU : in std_logic; read_rates_started : out std_logic := '0'; read_rates_done : out std_logic := '0'; new_config_started : out std_logic := '0'; new_config_done : out std_logic := '0'; ping_all_started : out std_logic := '0'; ping_all_done : out std_logic := '0'; config_single_FTU_started : out std_logic := '0'; config_single_FTU_done : out std_logic := '0'; ftu_active_cr0 : in std_logic_vector (15 downto 0); ftu_active_cr1 : in std_logic_vector (15 downto 0); ftu_active_cr2 : in std_logic_vector (15 downto 0); ftu_active_cr3 : in std_logic_vector (15 downto 0); config_single_FTU_param : in std_logic_vector (15 DOWNTO 0); ftu_error_calls : out std_logic_vector (15 DOWNTO 0) := (others => '0'); ftu_error_data : out std_logic_vector ((FTU_RS485_BLOCK_WIDTH - 1) downto 0) := (others => '0'); ftu_error_send : out std_logic := '0'; ftu_error_send_ack : in std_logic; ftu_error_send_ready : in std_logic; static_RAM_busy : in std_logic; static_RAM_started : in std_logic; static_RAM_ready : in std_logic; data_static_RAM : in std_logic_vector(15 downto 0) := (others => '0'); read_static_RAM : out std_logic := '0'; addr_static_RAM : out std_logic_vector(11 downto 0) := (others => '0'); dynamic_RAM_busy : in std_logic; dynamic_RAM_started : in std_logic; dynamic_RAM_ready : in std_logic; data_dynamic_RAM : out std_logic_vector(15 downto 0) := (others => '0'); write_dynamic_RAM : out std_logic := '0'; addr_dynamic_RAM : out std_logic_vector(11 downto 0) := (others => '0'); FTUlist_RAM_busy : in std_logic; FTUlist_RAM_started : in std_logic; FTUlist_RAM_ready : in std_logic; data_FTUlist_RAM : out std_logic_vector(15 downto 0) := (others => '0'); write_FTUlist_RAM : out std_logic := '0'; addr_FTUlist_RAM : out std_logic_vector(11 downto 0) := (others => '0') ); end component; component FTM_fad_broadcast port( clk_50MHz : in std_logic; rx_en : out STD_LOGIC; tx_en : out STD_LOGIC; rx_d_0 : in STD_LOGIC; tx_d_0 : out STD_LOGIC; rx_d_1 : in STD_LOGIC; tx_d_1 : out STD_LOGIC; rx_d_2 : in STD_LOGIC; tx_d_2 : out STD_LOGIC; rx_d_3 : in STD_LOGIC; tx_d_3 : out STD_LOGIC; enable_ID_sending : in std_logic; TIM_source : in std_logic; LP_settings : in std_logic_vector(3 downto 0); trigger_ID_ready : in std_logic; trigger_ID : in std_logic_vector(FAD_RS485_BLOCK_WIDTH - 1 downto 0); trigger_ID_read : out std_logic ); end component; component ethernet_modul port( wiz_reset : OUT std_logic := '1'; wiz_addr : OUT std_logic_vector (9 DOWNTO 0); wiz_data : INOUT std_logic_vector (15 DOWNTO 0); wiz_cs : OUT std_logic := '1'; wiz_wr : OUT std_logic := '1'; wiz_rd : OUT std_logic := '1'; wiz_int : IN std_logic ; clk : IN std_logic ; sd_ready : OUT std_logic ; sd_busy : OUT std_logic ; led : OUT std_logic_vector (7 DOWNTO 0); sd_read_ftu : IN std_logic ; sd_started_ftu : OUT std_logic := '0'; cc_R0 : OUT std_logic_vector (31 DOWNTO 0); cc_R1 : OUT std_logic_vector (31 DOWNTO 0); cc_R11 : OUT std_logic_vector (31 DOWNTO 0); cc_R13 : OUT std_logic_vector (31 DOWNTO 0); cc_R14 : OUT std_logic_vector (31 DOWNTO 0); cc_R15 : OUT std_logic_vector (31 DOWNTO 0); cc_R8 : OUT std_logic_vector (31 DOWNTO 0); cc_R9 : OUT std_logic_vector (31 DOWNTO 0); coin_n_c : OUT std_logic_vector (15 DOWNTO 0); coin_n_p : OUT std_logic_vector (15 DOWNTO 0); dead_time : OUT std_logic_vector (15 DOWNTO 0); general_settings : OUT std_logic_vector (15 DOWNTO 0); lp1_amplitude : OUT std_logic_vector (15 DOWNTO 0); lp1_delay : OUT std_logic_vector (15 DOWNTO 0); lp2_amplitude : OUT std_logic_vector (15 DOWNTO 0); lp2_delay : OUT std_logic_vector (15 DOWNTO 0); lp_pt_freq : OUT std_logic_vector (15 DOWNTO 0); lp_pt_ratio : OUT std_logic_vector (15 DOWNTO 0); timemarker_delay : OUT std_logic_vector (15 DOWNTO 0); trigger_delay : OUT std_logic_vector (15 DOWNTO 0); sd_addr_ftu : IN std_logic_vector (11 DOWNTO 0); sd_data_out_ftu : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); ftu_active_cr0 : OUT std_logic_vector (15 DOWNTO 0); ftu_active_cr1 : OUT std_logic_vector (15 DOWNTO 0); ftu_active_cr2 : OUT std_logic_vector (15 DOWNTO 0); ftu_active_cr3 : OUT std_logic_vector (15 DOWNTO 0); new_config : OUT std_logic := '0'; config_started : IN std_logic ; config_start_eth : IN std_logic ; config_started_eth : OUT std_logic := '0'; config_ready_eth : OUT std_logic := '0'; config_started_ack : OUT std_logic := '0'; fl_busy : OUT std_logic ; fl_ready : OUT std_logic ; fl_write_ftu : IN std_logic ; fl_started_ftu : OUT std_logic := '0'; fl_addr_ftu : IN std_logic_vector (11 DOWNTO 0); fl_data_in_ftu : IN std_logic_vector (15 DOWNTO 0) := (others => '0'); ping_ftu_start : OUT std_logic := '0'; ping_ftu_started : IN std_logic ; ping_ftu_ready : IN std_logic ; dd_write_ftu : IN std_logic ; dd_started_ftu : OUT std_logic := '0'; dd_data_in_ftu : IN std_logic_vector (15 DOWNTO 0); dd_addr_ftu : IN std_logic_vector (11 DOWNTO 0); dd_busy : OUT std_logic ; dd_ready : OUT std_logic ; coin_win_c : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); coin_win_p : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); --new stuff dd_block_ready_ftu : IN std_logic; dd_block_start_ack_ftu : OUT std_logic := '0'; dd_block_start_ftu : IN std_logic; dd_send : IN std_logic; dd_send_ack : OUT std_logic := '1'; dd_send_ready : OUT std_logic := '1'; --very new stuff ftu_error_calls : IN std_logic_vector (15 DOWNTO 0); ftu_error_data : IN std_logic_vector (223 DOWNTO 0); -- (28 * 8) - 1 ftu_error_send : IN std_logic; ftu_error_send_ack : OUT std_logic := '1'; ftu_error_send_ready : OUT std_logic := '1'; prescaling_FTU01 : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); trigger_counter : IN std_logic_vector (31 DOWNTO 0) := (others => '0'); trigger_counter_read : OUT std_logic := '0'; trigger_counter_valid : IN std_logic; --newest stuff board_id : IN std_logic_vector (63 DOWNTO 0); get_ts_counter : OUT std_logic := '0'; get_ts_counter_ready : IN std_logic; get_ts_counter_started : IN std_logic; timestamp_counter : IN std_logic_vector (47 DOWNTO 0); get_ot_counter : OUT std_logic := '0'; get_ot_counter_ready : IN std_logic; get_ot_counter_started : IN std_logic; on_time_counter : IN std_logic_vector (47 DOWNTO 0); temp_sensor_array : IN sensor_array_type; temp_sensor_ready : IN std_logic; crate_reset : OUT std_logic := '0'; crate_reset_ack : IN std_logic; crate_reset_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); start_run : OUT std_logic := '0'; start_run_ack : IN std_logic; stop_run : OUT std_logic := '0'; stop_run_ack : IN std_logic; current_cc_state : IN std_logic_vector (15 DOWNTO 0); start_run_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0'); start_run_num_events : OUT std_logic_vector (31 DOWNTO 0) := (others => '0'); new_config_ftu : OUT std_logic := '0'; new_config_ftu_ack : IN std_logic; new_config_ftu_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0') ); end component; -- component counter_dummy IS -- PORT( -- clk : IN std_logic; -- get_counter : IN std_logic; -- get_counter_started : OUT std_logic := '0'; -- get_counter_ready : OUT std_logic := '0'; -- counter : OUT std_logic_vector (47 DOWNTO 0) := (others => '0') -- ); -- end component; component Timing_counter is port( clk : in STD_LOGIC; -- 50 MHz system clock enable : in STD_LOGIC; -- enable counter reset : in Std_LOGIC; -- reset counter read_counter : in STD_LOGIC; -- read counter reading_started : out STD_LOGIC; reading_valid : out STD_LOGIC; -- counter reading at output ready counter_reading : out std_logic_vector (TC_WIDTH - 1 downto 0) ); end component; component Lightpulser_interface_Basic is port( clk_50 : IN STD_LOGIC; --clk_250 : IN STD_LOGIC; Cal_0_p : out STD_LOGIC := '0'; Cal_0_n : out STD_LOGIC := '1'; Cal_1_p : out STD_LOGIC := '0'; Cal_1_n : out STD_LOGIC := '1'; Cal_2_p : out STD_LOGIC := '0'; Cal_2_n : out STD_LOGIC := '1'; Cal_3_p : out STD_LOGIC := '0'; Cal_3_n : out STD_LOGIC := '1'; Cal_4_p : out STD_LOGIC := '0'; Cal_4_n : out STD_LOGIC := '1'; Cal_5_p : out STD_LOGIC := '0'; Cal_5_n : out STD_LOGIC := '1'; Cal_6_p : out STD_LOGIC := '0'; Cal_6_n : out STD_LOGIC := '1'; Cal_7_p : out STD_LOGIC := '0'; Cal_7_n : out STD_LOGIC := '1'; LP1_ampl : in std_logic_vector (15 downto 0); LP2_ampl : in std_logic_vector (15 downto 0); --LP1_delay : in std_logic_vector (15 downto 0); --LP2_delay : in std_logic_vector (15 downto 0); LP1_pulse : in std_logic; LP2_pulse : in std_logic; start_config : in std_logic; config_started : out std_logic := '0'; config_done : out std_logic := '0' ); end component; begin -- -- IBUFG: Single-ended global clock input buffer -- -- Spartan-3A -- -- Xilinx HDL Language Template, version 11.4 -- IBUFG_inst : IBUFG -- generic map ( -- IBUF_DELAY_VALUE => "0", -- Specify the amount of added input delay for buffer, -- -- "0"-"16" -- IOSTANDARD => "DEFAULT") -- port map ( -- O => clk_buf_sig, -- Clock buffer output -- I => clk -- Clock buffer input (connect directly to top-level port) -- ); -- Inst_FTM_clk_gen : FTM_clk_gen -- port map( -- clk => clk_buf_sig, -- rst => reset_sig, -- clk_1 => clk_1M_sig, -- clk_50 => clk_50M_sig, -- clk_250 => clk_250M_sig, -- clk_250_ps => clk_250M_ps_sig, -- ready => clk_ready_sig -- ); Inst_FTM_clk_gen_2 : FTM_clk_gen_2 port map( clk => clk, rst => reset_sig, clk_1 => clk_1M_sig, clk_50 => clk_50M_sig, clk_250 => clk_250M_sig, clk_250_ps => clk_250M_ps_sig, ready => clk_ready_sig ); Inst_FTM_dna_gen : FTM_dna_gen port map( clk => clk_50M_sig, start => dna_start_sig, dna => dna_sig, ready => dna_ready_sig ); --differential output buffer for trigger signal OBUFDS_LVDS_33_TRG : OBUFDS_LVDS_33 port map( O => TRG_p, OB => TRG_n, I => trigger_signal_sig ); --differential output buffer for TIM signal OBUFDS_LVDS_33_TIM : OBUFDS_LVDS_33 port map( O => TIM_Run_p, OB => TIM_Run_n, I => TIM_signal_sig ); --differential output buffer for fast reset signal OBUFDS_LVDS_33_RES : OBUFDS_LVDS_33 port map( O => RES_p, OB => RES_n, I => '0' ); Inst_trigger_manager : trigger_manager port map( --clocks clk_50MHz => clk_50M_sig, clk_250MHz => clk_250M_sig, clk_250MHz_180 => clk_250M_ps_sig, --trigger primitives from FTUs trig_prim_0 => Trig_Prim_A, --crate 0 trig_prim_1 => Trig_Prim_B, --crate 1 trig_prim_2 => Trig_Prim_C, --crate 2 trig_prim_3 => Trig_Prim_D, --crate 3 --external signals ext_trig_1 => ext_Trig(1), ext_trig_2 => ext_Trig(2), ext_veto => Veto, FAD_busy_0 => Busy0, --crate 0 FAD_busy_1 => Busy1, --crate 1 FAD_busy_2 => Busy2, --crate 2 FAD_busy_3 => Busy3, --crate 3 --control signals from e.g. main control start_run => trigger_start_sig, --enable trigger output stop_run => trigger_stop_sig, --disable trigger output new_config => config_trigger_sig, --settings register (see FTM Firmware Specifications) general_settings => general_settings_sig, LP_and_PED_freq => lp_pt_freq_sig, LP1_LP2_PED_ratio => lp_pt_ratio_sig, maj_coinc_n_phys => coin_n_p_sig, maj_coinc_n_calib => coin_n_c_sig, trigger_delay => trigger_delay_sig, TIM_delay => timemarker_delay_sig, dead_time => dead_time_sig, coinc_window_phys => coin_win_p_sig, coinc_window_calib => coin_win_c_sig, active_FTU_list_0 => ftu_active_cr0_sig, active_FTU_list_1 => ftu_active_cr1_sig, active_FTU_list_2 => ftu_active_cr2_sig, active_FTU_list_3 => ftu_active_cr3_sig, --control signals or information for other entities trigger_ID_read => trigger_ID_read_sig, trig_cnt_copy_read => trigger_counter_read_sig, trigger_ID_ready => trigger_ID_ready_sig, trigger_ID => trigger_ID_sig, trig_cnt_copy => trigger_counter_sig, --counter reading trig_cnt_copy_valid => trigger_counter_valid_sig, --trigger counter reading is valid trigger_active => trigger_active_sig, --phys triggers are enabled/active config_done => config_trigger_done_sig, LP1_pulse => LP1_pulse_sig, --send start signal to light pulser 1 LP2_pulse => LP2_pulse_sig, --send start signal to light pulser 2 --trigger and time marker output signals to FADs trigger_signal => trigger_signal_sig, TIM_signal => TIM_signal_sig ); Inst_Clock_cond_interface : Clock_cond_interface port map( clk => clk_50M_sig, CLK_Clk_Cond => CLK_Clk_Cond, LE_Clk_Cond => LE_Clk_Cond, DATA_Clk_Cond => DATA_Clk_Cond, SYNC_Clk_Cond => SYNC_Clk_Cond, LD_Clk_Cond => LD_Clk_Cond, TIM_Sel => TIM_Sel, cc_R0 => cc_R0_sig, cc_R1 => cc_R1_sig, cc_R8 => cc_R8_sig, cc_R9 => cc_R9_sig, cc_R11 => cc_R11_sig, cc_R13 => cc_R13_sig, cc_R14 => cc_R14_sig, cc_R15 => cc_R15_sig, start_config => config_start_cc_sig, config_started => config_started_cc_sig, config_done => config_ready_cc_sig, timemarker_select => general_settings_sig(0) ); Inst_FTM_central_control : FTM_central_control port map( clk => clk_50M_sig, clk_ready => clk_ready_sig, clk_scaler => clk_1M_sig, new_config => new_config_sig, config_started => config_started_sig, config_started_ack => config_started_ack_sig, config_start_eth => config_start_eth_sig, config_started_eth => config_started_eth_sig, config_ready_eth => config_ready_eth_sig, config_start_ftu => config_start_ftu_sig, config_started_ftu => config_started_ftu_sig, config_ready_ftu => config_ready_ftu_sig, ping_ftu_start => ping_ftu_start_sig, ping_ftu_started => ping_ftu_started_sig, ping_ftu_ready => ping_ftu_ready_sig, ping_ftu_start_ftu => ping_ftu_start_ftu_sig, ping_ftu_started_ftu => ping_ftu_started1_sig, ping_ftu_ready_ftu => ping_ftu_ready1_sig, rates_ftu => rates_ftu_start_sig, rates_started_ftu => rates_ftu_started_sig, rates_ready_ftu => rates_ftu_ready_sig, prescaling_FTU01 => prescaling_FTU01_sig(7 downto 0), dd_send => dd_send_sig, dd_send_ack => dd_send_ack_sig, dd_send_ready => dd_send_ready_sig, dd_block_ready_ftu => dd_block_ready_ftu_sig, dd_block_start_ack_ftu => dd_block_start_ack_ftu_sig, dd_block_start_ftu => dd_block_start_ftu_sig, config_start_cc => config_start_cc_sig, config_started_cc => config_started_cc_sig, config_ready_cc => config_ready_cc_sig, config_start_lp => config_start_lp_sig, config_started_lp => config_started_lp_sig, config_ready_lp => config_ready_lp_sig, config_trigger => config_trigger_sig, config_trigger_done => config_trigger_done_sig, dna_start => dna_start_sig, dna_ready => dna_ready_sig, crate_reset => crate_reset_sig, crate_reset_ack => crate_reset_ack_sig, crate_reset_param => crate_reset_param_sig, start_run => start_run_sig, start_run_ack => start_run_ack_sig, stop_run => stop_run_sig, stop_run_ack => stop_run_ack_sig, current_cc_state => current_cc_state_sig, cc_state_test => cc_state_test_sig, start_run_param => start_run_param_sig, start_run_num_events => start_run_num_events_sig, trigger_start => trigger_start_sig, trigger_stop => trigger_stop_sig, enable_ID_sending => enable_ID_sending_sig, reset_timer => reset_timer_sig, crate_res_0 => crate_res0_sig, crate_res_1 => crate_res1_sig, crate_res_2 => crate_res2_sig, crate_res_3 => crate_res3_sig, new_config_ftu => new_config_ftu_sig, new_config_ftu_ack => new_config_ftu_ack_sig, config_single_FTU => config_single_FTU_sig, config_single_FTU_started => config_single_FTU_started_sig, config_single_FTU_done => config_single_FTU_done_sig ); Inst_FTM_ftu_control : FTM_ftu_control port map( clk_50MHz => clk_50M_sig, rx_en => Bus1_Rx_En, tx_en => Bus1_Tx_En, rx_d_0 => Bus1_RxD_0, tx_d_0 => Bus1_TxD_0, rx_d_1 => Bus1_RxD_1, tx_d_1 => Bus1_TxD_1, rx_d_2 => Bus1_RxD_2, tx_d_2 => Bus1_TxD_2, rx_d_3 => Bus1_RxD_3, tx_d_3 => Bus1_TxD_3, new_config => config_start_ftu_sig, ping_all => ping_ftu_start_ftu_sig, read_rates => rates_ftu_start_sig, config_single_FTU => config_single_FTU_sig, read_rates_started => rates_ftu_started_sig, read_rates_done => rates_ftu_ready_sig, new_config_started => config_started_ftu_sig, new_config_done => config_ready_ftu_sig, ping_all_started => ping_ftu_started1_sig, ping_all_done => ping_ftu_ready1_sig, config_single_FTU_started => config_single_FTU_started_sig, config_single_FTU_done => config_single_FTU_done_sig, ftu_active_cr0 => ftu_active_cr0_sig, ftu_active_cr1 => ftu_active_cr1_sig, ftu_active_cr2 => ftu_active_cr2_sig, ftu_active_cr3 => ftu_active_cr3_sig, config_single_FTU_param => new_config_ftu_param_sig, ftu_error_calls => ftu_error_calls_sig, ftu_error_data => ftu_error_data_sig, ftu_error_send => ftu_error_send_sig, ftu_error_send_ack => ftu_error_send_ack_sig, ftu_error_send_ready=> ftu_error_send_ready_sig, static_RAM_busy => sd_busy_sig, static_RAM_started => sd_started_ftu_sig, static_RAM_ready => sd_ready_sig, data_static_RAM => sd_data_out_ftu_sig, read_static_RAM => sd_read_ftu_sig, addr_static_RAM => sd_addr_ftu_sig, dynamic_RAM_busy => dd_busy_sig, dynamic_RAM_started => dd_started_ftu_sig, dynamic_RAM_ready => dd_ready_sig, data_dynamic_RAM => dd_data_sig, write_dynamic_RAM => dd_write_sig, addr_dynamic_RAM => dd_addr_sig, FTUlist_RAM_busy => fl_busy_sig, FTUlist_RAM_started => fl_started_ftu_sig, FTUlist_RAM_ready => fl_ready_sig, data_FTUlist_RAM => fl_data_sig, write_FTUlist_RAM => fl_write_sig, addr_FTUlist_RAM => fl_addr_sig ); Inst_FTM_fad_broadcast : FTM_fad_broadcast port map( clk_50MHz => clk_50M_sig, rx_en => Bus2_Rx_En, tx_en => Bus2_Tx_En, rx_d_0 => Bus2_RxD_0, tx_d_0 => Bus2_TxD_0, rx_d_1 => Bus2_RxD_1, tx_d_1 => Bus2_TxD_1, rx_d_2 => Bus2_RxD_2, tx_d_2 => Bus2_TxD_2, rx_d_3 => Bus2_RxD_3, tx_d_3 => Bus2_TxD_3, enable_ID_sending => enable_ID_sending_sig, TIM_source => general_settings_sig(0), LP_settings => "0000", trigger_ID_ready => trigger_ID_ready_sig, trigger_ID => trigger_ID_sig, trigger_ID_read => trigger_ID_read_sig ); Inst_ethernet_modul : ethernet_modul port map( wiz_reset => W_RES, wiz_addr => W_A, wiz_data => W_D, wiz_cs => W_CS, wiz_wr => W_WR, wiz_rd => W_RD, wiz_int => W_INT, clk => clk_50M_sig, sd_ready => sd_ready_sig, sd_busy => sd_busy_sig, led => led_sig, sd_read_ftu => sd_read_ftu_sig, sd_started_ftu => sd_started_ftu_sig, cc_R0 => cc_R0_sig, cc_R1 => cc_R1_sig, cc_R11 => cc_R11_sig, cc_R13 => cc_R13_sig, cc_R14 => cc_R14_sig, cc_R15 => cc_R15_sig, cc_R8 => cc_R8_sig, cc_R9 => cc_R9_sig, coin_n_c => coin_n_c_sig, coin_n_p => coin_n_p_sig, dead_time => dead_time_sig, general_settings => general_settings_sig, lp1_amplitude => lp1_amplitude_sig, lp1_delay => lp1_delay_sig, lp2_amplitude => lp2_amplitude_sig, lp2_delay => lp2_delay_sig, lp_pt_freq => lp_pt_freq_sig, lp_pt_ratio => lp_pt_ratio_sig, timemarker_delay => timemarker_delay_sig, trigger_delay => trigger_delay_sig, sd_addr_ftu => sd_addr_ftu_sig, sd_data_out_ftu => sd_data_out_ftu_sig, ftu_active_cr0 => ftu_active_cr0_sig, ftu_active_cr1 => ftu_active_cr1_sig, ftu_active_cr2 => ftu_active_cr2_sig, ftu_active_cr3 => ftu_active_cr3_sig, new_config => new_config_sig, config_started => config_started_sig, config_start_eth => config_start_eth_sig, config_started_eth => config_started_eth_sig, config_ready_eth => config_ready_eth_sig, config_started_ack => config_started_ack_sig, fl_busy => fl_busy_sig, fl_ready => fl_ready_sig, fl_write_ftu => fl_write_sig, fl_started_ftu => fl_started_ftu_sig, fl_addr_ftu => fl_addr_sig, fl_data_in_ftu => fl_data_sig, ping_ftu_start => ping_ftu_start_sig, ping_ftu_started => ping_ftu_started_sig, ping_ftu_ready => ping_ftu_ready_sig, dd_write_ftu => dd_write_sig, dd_started_ftu => dd_started_ftu_sig, dd_data_in_ftu => dd_data_sig, dd_addr_ftu => dd_addr_sig, dd_busy => dd_busy_sig, dd_ready => dd_ready_sig, coin_win_c => coin_win_c_sig, coin_win_p => coin_win_p_sig, --new stuff dd_block_ready_ftu => dd_block_ready_ftu_sig, dd_block_start_ack_ftu => dd_block_start_ack_ftu_sig, dd_block_start_ftu => dd_block_start_ftu_sig, dd_send => dd_send_sig, dd_send_ack => dd_send_ack_sig, dd_send_ready => dd_send_ready_sig, --very new stuff ftu_error_calls => ftu_error_calls_sig, ftu_error_data => ftu_error_data_sig, ftu_error_send => ftu_error_send_sig, ftu_error_send_ack => ftu_error_send_ack_sig, ftu_error_send_ready => ftu_error_send_ready_sig, prescaling_FTU01 => prescaling_FTU01_sig, trigger_counter => trigger_counter_sig, trigger_counter_read => trigger_counter_read_sig, trigger_counter_valid => trigger_counter_valid_sig, --newest stuff board_id => dna_sig, get_ts_counter => get_ts_counter_sig, get_ts_counter_ready => get_ts_counter_ready_sig, get_ts_counter_started => get_ts_counter_started_sig, timestamp_counter => timestamp_counter_sig, get_ot_counter => get_ot_counter_sig, get_ot_counter_ready => get_ot_counter_ready_sig, get_ot_counter_started => get_ot_counter_started_sig, on_time_counter => on_time_counter_sig, temp_sensor_array => (35, 45, 55, 65), temp_sensor_ready => '1', crate_reset => crate_reset_sig, crate_reset_ack => crate_reset_ack_sig, crate_reset_param => crate_reset_param_sig, start_run => start_run_sig, start_run_ack => start_run_ack_sig, stop_run => stop_run_sig, stop_run_ack => stop_run_ack_sig, current_cc_state => current_cc_state_sig, start_run_param => start_run_param_sig, start_run_num_events => start_run_num_events_sig, new_config_ftu => new_config_ftu_sig, new_config_ftu_ack => new_config_ftu_ack_sig, new_config_ftu_param => new_config_ftu_param_sig ); -- Inst_counter_dummy_ts : counter_dummy -- port map( -- clk => clk_50M_sig, -- get_counter => get_ts_counter_sig, -- get_counter_started => get_ts_counter_started_sig, -- get_counter_ready => get_ts_counter_ready_sig, -- counter => timestamp_counter_sig -- ); -- Inst_counter_dummy_ot : counter_dummy -- port map( -- clk => clk_50M_sig, -- get_counter => get_ot_counter_sig, -- get_counter_started => get_ot_counter_started_sig, -- get_counter_ready => get_ot_counter_ready_sig, -- counter => on_time_counter_sig -- ); Inst_Timing_counter_ts : Timing_counter port map( clk => clk_50M_sig, enable => '1', reset => reset_timer_sig, read_counter => get_ts_counter_sig, reading_started => get_ts_counter_started_sig, reading_valid => get_ts_counter_ready_sig, counter_reading => timestamp_counter_sig ); Inst_Timing_counter_ot : Timing_counter port map( clk => clk_50M_sig, enable => trigger_active_sig, reset => reset_timer_sig, read_counter => get_ot_counter_sig, reading_started => get_ot_counter_started_sig, reading_valid => get_ot_counter_ready_sig, counter_reading => on_time_counter_sig ); Inst_Lightpulser_interface_Basic : Lightpulser_interface_Basic port map ( clk_50 => clk_50M_sig, --clk_250 => clk_250M_sig, Cal_0_p => Cal_2_p, --swapped with Cal_2_p due to connector on FLD board Cal_0_n => Cal_2_n, --swapped with Cal_2_n due to connector on FLD board Cal_1_p => Cal_1_p, Cal_1_n => Cal_1_n, Cal_2_p => Cal_0_p, --swapped with Cal_0_p due to connector on FLD board Cal_2_n => Cal_0_n, --swapped with Cal_0_n due to connector on FLD board Cal_3_p => Cal_3_p, Cal_3_n => Cal_3_n, Cal_4_p => Cal_6_p, --swapped with Cal_6_p due to connector on FLD board Cal_4_n => Cal_6_n, --swapped with Cal_6_n due to connector on FLD board Cal_5_p => Cal_5_p, Cal_5_n => Cal_5_n, Cal_6_p => Cal_4_p, --swapped with Cal_4_p due to connector on FLD board Cal_6_n => Cal_4_n, --swapped with Cal_4_n due to connector on FLD board Cal_7_p => Cal_7_p, Cal_7_n => Cal_7_n, LP1_ampl => lp1_amplitude_sig, LP2_ampl => lp2_amplitude_sig, --LP1_delay => lp1_delay_sig, --LP2_delay => lp2_delay_sig, LP1_pulse => LP1_pulse_sig, LP2_pulse => LP2_pulse_sig, start_config => config_start_lp_sig, config_started => config_started_lp_sig, config_done => config_ready_lp_sig ); LED_red <= led_sig(3 downto 0); LED_ye <= led_sig(5 downto 4); LED_gn <= led_sig(7 downto 6); TP(32 downto 8) <= (others => '0'); --TP(8) <= clk_50M_sig; TP( 7 downto 0) <= cc_state_test_sig; Crate_Res0 <= crate_res0_sig; Crate_Res1 <= crate_res1_sig; Crate_Res2 <= crate_res2_sig; Crate_Res3 <= crate_res3_sig; end Behavioral;