source: firmware/FTM/FTM_top.vhd@ 13716

Last change on this file since 13716 was 12029, checked in by weitzel, 13 years ago
FTM: firmware version 6 committed with new IP address and LEDs off
File size: 57.4 KB
Line 
1----------------------------------------------------------------------------------
2-- Company: ETH Zurich, Institute for Particle Physics
3-- Engineer: P. Vogler, Q. Weitzel
4--
5-- Create Date: 08 December 2010
6-- Design Name:
7-- Module Name: FTM_top - Behavioral
8-- Project Name:
9-- Target Devices:
10-- Tool versions:
11-- Description: Top level entity for FTM firmware
12--
13--
14-- Dependencies:
15--
16-- Revision:
17-- Revision 0.01 - File Created
18-- Additional Comments:
19--
20----------------------------------------------------------------------------------
21
22library IEEE;
23use IEEE.STD_LOGIC_1164.ALL;
24use IEEE.STD_LOGIC_ARITH.ALL;
25use IEEE.STD_LOGIC_UNSIGNED.ALL;
26
27library ftm_definitions;
28USE ftm_definitions.ftm_array_types.all;
29USE ftm_definitions.ftm_constants.all;
30
31---- Uncomment the following library declaration if instantiating
32---- any Xilinx primitives in this code.
33library UNISIM;
34use UNISIM.VComponents.all;
35
36
37entity FTM_top is
38 port(
39
40 -- Clock
41 clk : IN STD_LOGIC; -- external clock from oscillator U47
42
43 -- connection to the WIZnet W5300 ethernet controller
44 -- on IO-Bank 1
45 -------------------------------------------------------------------------------
46 -- W5300 data bus
47 W_D : inout STD_LOGIC_VECTOR(15 downto 0); -- 16-bit data bus to W5300
48
49 -- W5300 address bus
50 W_A : out STD_LOGIC_VECTOR(9 downto 0); -- there is no real net W_A0 because
51 -- the W5300 is operated in the
52 -- 16-bit mode
53 -- -> W_A<0> assigned to unconnected pin
54
55 -- W5300 control signals
56 -- the signals W_INT, W_RD, W_WR and W_RES also go to testpoints T17
57 -- W_CS is also routed to testpoint JP7
58 W_CS : out STD_LOGIC := '1'; -- W5300 chip select
59 W_INT : IN STD_LOGIC; -- interrupt
60 W_RD : out STD_LOGIC := '1'; -- read
61 W_WR : out STD_LOGIC := '1'; -- write
62 W_RES : out STD_LOGIC := '1'; -- reset W5300 chip
63
64 -- W5300 buffer ready indicator
65 -- W_BRDY : in STD_LOGIC_VECTOR(3 downto 0);
66
67 -- testpoints (T18) associated with the W5300 on IO-bank 1
68 -- W_T : inout STD_LOGIC_VECTOR(3 downto 0);
69
70
71 -- SPI Interface
72 -- connection to the EEPROM U36 (AL25L016M) and
73 -- temperature sensors U45, U46, U48 and U49 (all MAX6662)
74 -- on IO-Bank 1
75 -------------------------------------------------------------------------------
76 -- S_CLK : out STD_LOGIC; -- SPI clock
77
78 -- EEPROM
79 -- MOSI : out STD_LOGIC; -- master out slave in
80 -- MISO : in STD_LOGIC; -- master in slave out
81 -- EE_CS : out STD_LOGIC; -- EEPROM chip select
82
83 -- temperature sensors U45, U46, U48 and U49
84 -- SIO : inout STD_LOGIC; -- serial IO
85 -- TS_CS : out STD_LOGIC_VECTOR(3 downto 0); -- temperature sensors chip select
86
87
88 -- Trigger primitives inputs
89 -- on IO-Bank 2
90 -------------------------------------------------------------------------------
91 Trig_Prim_A : in STD_LOGIC_VECTOR(9 downto 0); -- crate 0
92 Trig_Prim_B : in STD_LOGIC_VECTOR(9 downto 0); -- crate 1
93 Trig_Prim_C : in STD_LOGIC_VECTOR(9 downto 0); -- crate 2
94 Trig_Prim_D : in STD_LOGIC_VECTOR(9 downto 0); -- crate 3
95
96
97 -- NIM inputs
98 ------------------------------------------------------------------------------
99 -- on IO-Bank 3
100 ext_Trig : in STD_LOGIC_VECTOR(2 downto 1); -- external trigger input
101 Veto : in STD_LOGIC; -- trigger veto input
102 -- NIM_In : in STD_LOGIC_VECTOR(2 downto 0); -- auxiliary inputs
103
104 -- on IO-Bank 0
105 -- alternative external clock input for FPGA
106 -- NIM_In3_GCLK : in STD_LOGIC; -- input with global clock buffer available
107
108
109 -- LEDs on IO-Banks 0 and 3
110 -------------------------------------------------------------------------------
111 LED_red : out STD_LOGIC_VECTOR(3 downto 0); -- red
112 LED_ye : out STD_LOGIC_VECTOR(1 downto 0); -- yellow
113 LED_gn : out STD_LOGIC_VECTOR(1 downto 0); -- green
114
115
116 -- Clock conditioner LMK03000
117 -- on IO-Bank 3
118 -------------------------------------------------------------------------------
119 CLK_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface serial clock
120 LE_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface latch enable
121 DATA_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface data
122
123 SYNC_Clk_Cond : out STD_LOGIC; -- global clock synchronization
124 LD_Clk_Cond : in STD_LOGIC; -- lock detect
125
126
127 -- various RS-485 Interfaces
128 -- on IO-Bank 3
129 -------------------------------------------------------------------------------
130 -- Bus 1: FTU slow control
131 Bus1_Tx_En : out STD_LOGIC; -- bus 1: transmitter enable
132 Bus1_Rx_En : out STD_LOGIC; -- bus 1: receiver enable
133
134 Bus1_RxD_0 : in STD_LOGIC; -- crate 0
135 Bus1_TxD_0 : out STD_LOGIC;
136
137 Bus1_RxD_1 : in STD_LOGIC; -- crate 1
138 Bus1_TxD_1 : out STD_LOGIC;
139
140 Bus1_RxD_2 : in STD_LOGIC; -- crate 2
141 Bus1_TxD_2 : out STD_LOGIC;
142
143 Bus1_RxD_3 : in STD_LOGIC; -- crate 3
144 Bus1_TxD_3 : out STD_LOGIC;
145
146
147 -- Bus 2: Trigger-ID to FAD boards
148 Bus2_Tx_En : out STD_LOGIC; -- bus 2: transmitter enable
149 Bus2_Rx_En : out STD_LOGIC; -- bus 2: receiver enable
150
151 Bus2_RxD_0 : in STD_LOGIC; -- crate 0
152 Bus2_TxD_0 : out STD_LOGIC;
153
154 Bus2_RxD_1 : in STD_LOGIC; -- crate 1
155 Bus2_TxD_1 : out STD_LOGIC;
156
157 Bus2_RxD_2 : in STD_LOGIC; -- crate 2
158 Bus2_TxD_2 : out STD_LOGIC;
159
160 Bus2_RxD_3 : in STD_LOGIC; -- crate 3
161 Bus2_TxD_3 : out STD_LOGIC;
162
163
164 -- auxiliary access
165 -- Aux_Rx_D : in STD_LOGIC;
166 -- Aux_Tx_D : out STD_LOGIC;
167 -- Aux_Rx_En : out STD_LOGIC; -- Rx- and Tx enable
168 -- Aux_Tx_En : out STD_LOGIC; -- also for auxiliary Trigger-ID
169
170
171 -- auxiliary Trigger-ID (i.e. to send the Trigger-ID to the counting hut/house/container)
172 -- TrID_Rx_D : in STD_LOGIC;
173 -- TrID_Tx_D : out STD_LOGIC;
174
175
176 -- Crate-Resets
177 -- on IO-Bank 3
178 -------------------------------------------------------------------------------
179 Crate_Res0 : out STD_LOGIC;
180 Crate_Res1 : out STD_LOGIC;
181 Crate_Res2 : out STD_LOGIC;
182 Crate_Res3 : out STD_LOGIC;
183
184
185 -- Busy signals from the FAD boards
186 -- on IO-Bank 3
187 -------------------------------------------------------------------------------
188 Busy0 : in STD_LOGIC;
189 Busy1 : in STD_LOGIC;
190 Busy2 : in STD_LOGIC;
191 Busy3 : in STD_LOGIC;
192
193
194 -- NIM outputs
195 -- on IO-Bank 0
196 -- LVDS output at the FPGA followed by LVDS to NIM conversion stage
197 -------------------------------------------------------------------------------
198 -- calibration
199 -- Cal_NIM1_p : out STD_LOGIC; -- Cal_NIM1+
200 -- Cal_NIM1_n : out STD_LOGIC; -- Cal_NIM1-
201 -- Cal_NIM2_p : out STD_LOGIC; -- Cal_NIM2+
202 -- Cal_NIM2_n : out STD_LOGIC; -- Cal_NIM2-
203
204 -- auxiliarry / spare NIM outputs
205 -- NIM_Out0_p : out STD_LOGIC; -- NIM_Out0+
206 -- NIM_Out0_n : out STD_LOGIC; -- NIM_Out0-
207 -- NIM_Out1_p : out STD_LOGIC; -- NIM_Out1+
208 -- NIM_Out1_n : out STD_LOGIC; -- NIM_Out1-
209
210
211 -- fast control signal outputs
212 -- LVDS output at the FPGA followed by LVDS to NIM conversion stage
213 -------------------------------------------------------------------------------
214 RES_p : out STD_LOGIC; -- RES+ Reset
215 RES_n : out STD_LOGIC; -- RES- IO-Bank 0
216
217 TRG_p : out STD_LOGIC; -- TRG+ Trigger
218 TRG_n : out STD_LOGIC; -- TRG- IO-Bank 0
219
220 TIM_Run_p : out STD_LOGIC; -- TIM_Run+ Time Marker
221 TIM_Run_n : out STD_LOGIC; -- TIM_Run- IO-Bank 2
222 TIM_Sel : out STD_LOGIC; -- Time Marker selector on IO-Bank 2
223
224 -- CLD_FPGA : in STD_LOGIC; -- DRS-Clock feedback into FPGA
225
226
227 -- LVDS calibration outputs
228 -- on IO-Bank 0
229 -------------------------------------------------------------------------------
230 -- to connector J13
231 -- for light pulsar in the mirror dish
232 Cal_0_p : out STD_LOGIC;
233 Cal_0_n : out STD_LOGIC;
234 Cal_1_p : out STD_LOGIC;
235 Cal_1_n : out STD_LOGIC;
236 Cal_2_p : out STD_LOGIC;
237 Cal_2_n : out STD_LOGIC;
238 Cal_3_p : out STD_LOGIC;
239 Cal_3_n : out STD_LOGIC;
240
241 -- to connector J12
242 -- for light pulsar inside shutter
243 Cal_4_p : out STD_LOGIC;
244 Cal_4_n : out STD_LOGIC;
245 Cal_5_p : out STD_LOGIC;
246 Cal_5_n : out STD_LOGIC;
247 Cal_6_p : out STD_LOGIC;
248 Cal_6_n : out STD_LOGIC;
249 Cal_7_p : out STD_LOGIC;
250 Cal_7_n : out STD_LOGIC;
251
252
253 -- Testpoints
254 -------------------------------------------------------------------------------
255 TP : inout STD_LOGIC_VECTOR(32 downto 0)
256 -- TP_in : in STD_LOGIC_VECTOR(34 downto 33); -- input only
257
258 -- Board ID - inputs
259 -- local board-ID "solder programmable"
260 -- all on 'input only' pins
261 -------------------------------------------------------------------------------
262 -- brd_id : in STD_LOGIC_VECTOR(7 downto 0) -- input only
263
264 );
265end FTM_top;
266
267architecture Behavioral of FTM_top is
268
269 signal cc_R0_sig : std_logic_vector(31 DOWNTO 0);
270 signal cc_R1_sig : std_logic_vector(31 DOWNTO 0);
271 signal cc_R11_sig : std_logic_vector(31 DOWNTO 0);
272 signal cc_R13_sig : std_logic_vector(31 DOWNTO 0);
273 signal cc_R14_sig : std_logic_vector(31 DOWNTO 0);
274 signal cc_R15_sig : std_logic_vector(31 DOWNTO 0);
275 signal cc_R8_sig : std_logic_vector(31 DOWNTO 0);
276 signal cc_R9_sig : std_logic_vector(31 DOWNTO 0);
277 signal coin_n_c_sig : std_logic_vector(15 DOWNTO 0);
278 signal coin_n_p_sig : std_logic_vector(15 DOWNTO 0);
279 signal dead_time_sig : std_logic_vector(15 DOWNTO 0);
280 signal ftu_active_cr0_sig : std_logic_vector(15 DOWNTO 0);
281 signal ftu_active_cr1_sig : std_logic_vector(15 DOWNTO 0);
282 signal ftu_active_cr2_sig : std_logic_vector(15 DOWNTO 0);
283 signal ftu_active_cr3_sig : std_logic_vector(15 DOWNTO 0);
284 signal general_settings_sig : std_logic_vector(15 DOWNTO 0);
285 signal lp1_amplitude_sig : std_logic_vector(15 DOWNTO 0);
286 signal lp1_delay_sig : std_logic_vector(15 DOWNTO 0);
287 signal lp2_amplitude_sig : std_logic_vector(15 DOWNTO 0);
288 signal lp2_delay_sig : std_logic_vector(15 DOWNTO 0);
289 signal lp_pt_freq_sig : std_logic_vector(15 DOWNTO 0);
290 signal lp_pt_ratio_sig : std_logic_vector(15 DOWNTO 0);
291 signal timemarker_delay_sig : std_logic_vector(15 DOWNTO 0);
292 signal trigger_delay_sig : std_logic_vector(15 DOWNTO 0);
293 signal sd_addr_ftu_sig : std_logic_vector(11 DOWNTO 0);
294 signal sd_busy_sig : std_logic;
295 signal sd_data_out_ftu_sig : std_logic_vector(15 DOWNTO 0) := (others => '0');
296 signal sd_read_ftu_sig : std_logic;
297 signal sd_ready_sig : std_logic;
298 signal sd_started_ftu_sig : std_logic := '0';
299 signal new_config_sig : std_logic := '0';
300 signal config_started_sig : std_logic := '0';
301 signal config_start_eth_sig : std_logic := '0';
302 signal config_started_eth_sig : std_logic := '0';
303 signal config_ready_eth_sig : std_logic := '0';
304 signal config_started_ack_sig : std_logic := '0';
305 signal ping_ftu_start_sig : std_logic := '0';
306 signal ping_ftu_started_sig : std_logic := '0';
307 signal ping_ftu_ready_sig : std_logic := '0';
308 signal config_start_ftu_sig : std_logic := '0';
309 signal config_started_ftu_sig : std_logic := '0';
310 signal config_ready_ftu_sig : std_logic := '0';
311 signal rates_ftu_start_sig : std_logic := '0';
312 signal rates_ftu_started_sig : std_logic := '0';
313 signal rates_ftu_ready_sig : std_logic := '0';
314 signal fl_busy_sig : std_logic;
315 signal fl_ready_sig : std_logic;
316 signal fl_write_sig : std_logic := '0';
317 signal fl_started_ftu_sig : std_logic := '0';
318 signal fl_addr_sig : std_logic_vector(11 DOWNTO 0) := (others => '0');
319 signal fl_data_sig : std_logic_vector(15 DOWNTO 0) := (others => '0');
320 signal ping_ftu_start_ftu_sig : std_logic := '0';
321 signal ping_ftu_started1_sig : std_logic := '0';
322 signal ping_ftu_ready1_sig : std_logic := '0';
323 signal coin_win_c_sig : std_logic_vector(15 DOWNTO 0) := (others => '0');
324 signal coin_win_p_sig : std_logic_vector(15 DOWNTO 0) := (others => '0');
325 --new or changed stuff
326 signal dd_data_sig : std_logic_vector(15 DOWNTO 0) := (others => '0');
327 signal dd_addr_sig : std_logic_vector(11 DOWNTO 0) := (others => '0');
328 signal dd_block_start_ftu_sig : std_logic := '0';
329 signal dd_block_start_ack_ftu_sig : std_logic := '0';
330 signal dd_block_ready_ftu_sig : std_logic := '0';
331 signal dd_busy_sig : std_logic;
332 signal dd_write_sig : std_logic := '0';
333 signal dd_started_ftu_sig : std_logic := '0';
334 signal dd_ready_sig : std_logic;
335 signal dd_send_sig : std_logic := '1';
336 signal dd_send_ack_sig : std_logic := '1';
337 signal dd_send_ready_sig : std_logic := '1';
338 --very new stuff
339 SIGNAL ftu_error_send_ack_sig : std_logic := '1';
340 SIGNAL ftu_error_send_ready_sig : std_logic := '1';
341 SIGNAL ftu_error_calls_sig : std_logic_vector(15 DOWNTO 0) := X"0000";
342 SIGNAL ftu_error_data_sig : std_logic_vector(223 DOWNTO 0) := (others => '0');
343 SIGNAL ftu_error_send_sig : std_logic := '0';
344 signal prescaling_FTU01_sig : std_logic_vector (15 DOWNTO 0);
345 signal trigger_counter_sig : std_logic_vector (31 DOWNTO 0);
346 signal trigger_counter_read_sig : std_logic;
347 signal trigger_counter_valid_sig : std_logic;
348
349 signal config_start_cc_sig : std_logic; -- initialized in central control
350 signal config_started_cc_sig : std_logic := '0';
351 signal config_ready_cc_sig : std_logic := '0';
352 signal cc_locked_sig : std_logic := '0';
353
354 signal config_start_lp_sig : std_logic; -- initialized in central control
355 signal config_started_lp_sig : std_logic; -- initialized in light pulser interface
356 signal config_ready_lp_sig : std_logic; -- initialized in light pulser interface
357
358 signal config_trigger_sig : std_logic;
359 signal config_trigger_done_sig : std_logic;
360
361 signal clk_buf_sig : std_logic;
362 signal clk_1M_sig : STD_LOGIC; -- generated from 50M clock by divider
363 signal clk_50M_sig : STD_LOGIC; -- generated by internal DCM
364 signal clk_250M_sig : STD_LOGIC; -- generated by internal DCM
365 signal clk_250M_ps_sig : STD_LOGIC; -- generated by internal DCM
366 signal clk_ready_sig : STD_LOGIC := '0'; -- set high by FTM_clk_gen when DCMs have locked
367
368 signal trigger_ID_ready_sig : std_logic; -- initialized in trigger manager
369 signal trigger_ID_sig : std_logic_vector(55 downto 0); -- initialized in trigger manager
370 signal trigger_ID_read_sig : std_logic; -- initialized in FTM_fad_broadcast
371
372 signal trigger_active_sig : std_logic; -- initialized in trigger manager
373
374 signal reset_sig : STD_LOGIC := '0'; -- initialize to 0 on power-up
375
376 signal trigger_signal_sig : std_logic := '0';
377 signal TIM_signal_sig : std_logic := '0';
378
379 --signals for FPGA DNA identifier
380 signal dna_sig : STD_LOGIC_VECTOR(63 downto 0); -- initialized in FTM_dna_gen
381 signal dna_start_sig : STD_LOGIC; -- initialized in FTM_central_control
382 signal dna_ready_sig : STD_LOGIC; -- initialized in FTM_dna_gen
383
384 signal led_sig : std_logic_vector(7 downto 0) := (others => '0');
385
386 signal get_ot_counter_sig : std_logic;
387 signal get_ot_counter_started_sig : std_logic;
388 signal get_ot_counter_ready_sig : std_logic;
389 signal on_time_counter_sig : std_logic_vector(47 downto 0);
390
391 signal get_ts_counter_sig : std_logic;
392 signal get_ts_counter_started_sig : std_logic;
393 signal get_ts_counter_ready_sig : std_logic;
394 signal timestamp_counter_sig : std_logic_vector(47 downto 0);
395
396 signal crate_reset_sig : std_logic;
397 signal crate_reset_ack_sig : std_logic;
398 signal crate_reset_param_sig : std_logic_vector (15 DOWNTO 0);
399 signal start_run_sig : std_logic;
400 signal start_run_ack_sig : std_logic;
401 signal stop_run_sig : std_logic;
402 signal stop_run_ack_sig : std_logic;
403 signal current_cc_state_sig : std_logic_vector (15 DOWNTO 0);
404 signal cc_state_test_sig : std_logic_vector ( 7 downto 0);
405 signal start_run_param_sig : std_logic_vector (15 DOWNTO 0);
406 signal start_run_num_events_sig : std_logic_vector (31 DOWNTO 0);
407
408 signal trigger_start_sig : std_logic;
409 signal trigger_stop_sig : std_logic;
410
411 signal enable_ID_sending_sig : std_logic;
412 signal reset_timer_sig : std_logic; -- initialized in FTM_central_control
413
414 signal crate_res0_sig : std_logic; -- initialized in FTM_central_control
415 signal crate_res1_sig : std_logic; -- initialized in FTM_central_control
416 signal crate_res2_sig : std_logic; -- initialized in FTM_central_control
417 signal crate_res3_sig : std_logic; -- initialized in FTM_central_control
418
419 signal LP1_pulse_sig : std_logic := '0';
420 signal LP2_pulse_sig : std_logic := '0';
421
422 signal new_config_ftu_sig : std_logic; -- initialized in ethernet_modul
423 signal new_config_ftu_ack_sig : std_logic; -- initialized in FTM_central_control
424 signal new_config_ftu_param_sig : std_logic_vector (15 DOWNTO 0); -- initialized in ethernet_modul
425
426 signal config_single_FTU_sig : std_logic; -- initialized in FTM_central_control
427 signal config_single_FTU_started_sig : std_logic; -- initialized in FTM_ftu_control
428 signal config_single_FTU_done_sig : std_logic; -- initialized in FTM_ftu_control
429
430-- component FTM_clk_gen
431-- port(
432-- clk : IN STD_LOGIC;
433-- rst : IN STD_LOGIC;
434-- clk_1 : OUT STD_LOGIC;
435-- clk_50 : OUT STD_LOGIC;
436-- clk_250 : OUT STD_LOGIC;
437-- clk_250_ps : OUT STD_LOGIC;
438-- ready : OUT STD_LOGIC
439-- );
440-- end component;
441
442 component FTM_clk_gen_2
443 port(
444 clk : IN STD_LOGIC;
445 rst : IN STD_LOGIC;
446 clk_1 : OUT STD_LOGIC;
447 clk_50 : OUT STD_LOGIC;
448 clk_250 : OUT STD_LOGIC;
449 clk_250_ps : OUT STD_LOGIC;
450 ready : OUT STD_LOGIC
451 );
452 end component;
453
454 component FTM_dna_gen
455 port(
456 clk : IN STD_LOGIC;
457 start : IN STD_LOGIC;
458 dna : OUT STD_LOGIC_VECTOR(63 downto 0);
459 ready : OUT STD_LOGIC
460 );
461 end component;
462
463 component trigger_manager
464 port(
465 --clocks
466 clk_50MHz : in std_logic;
467 clk_250MHz : in std_logic;
468 clk_250MHz_180 : in std_logic;
469 --trigger primitives from FTUs
470 trig_prim_0 : in std_logic_vector(9 downto 0); --crate 0
471 trig_prim_1 : in std_logic_vector(9 downto 0); --crate 1
472 trig_prim_2 : in std_logic_vector(9 downto 0); --crate 2
473 trig_prim_3 : in std_logic_vector(9 downto 0); --crate 3
474 --external signals
475 ext_trig_1 : in std_logic;
476 ext_trig_2 : in std_logic;
477 ext_veto : in std_logic;
478 FAD_busy_0 : in std_logic; --crate 0
479 FAD_busy_1 : in std_logic; --crate 1
480 FAD_busy_2 : in std_logic; --crate 2
481 FAD_busy_3 : in std_logic; --crate 3
482 --control signals from e.g. main control
483 start_run : in std_logic; --enable trigger output
484 stop_run : in std_logic; --disable trigger output
485 new_config : in std_logic;
486 --settings register (see FTM Firmware Specifications)
487 general_settings : in std_logic_vector(15 downto 0);
488 LP_and_PED_freq : in std_logic_vector(15 downto 0);
489 LP1_LP2_PED_ratio : in std_logic_vector(15 downto 0);
490 maj_coinc_n_phys : in std_logic_vector(15 downto 0);
491 maj_coinc_n_calib : in std_logic_vector(15 downto 0);
492 trigger_delay : in std_logic_vector(15 downto 0);
493 TIM_delay : in std_logic_vector(15 downto 0);
494 dead_time : in std_logic_vector(15 downto 0);
495 coinc_window_phys : in std_logic_vector(15 downto 0);
496 coinc_window_calib : in std_logic_vector(15 downto 0);
497 active_FTU_list_0 : in std_logic_vector(15 downto 0);
498 active_FTU_list_1 : in std_logic_vector(15 downto 0);
499 active_FTU_list_2 : in std_logic_vector(15 downto 0);
500 active_FTU_list_3 : in std_logic_vector(15 downto 0);
501 --control signals or information for other entities
502 trigger_ID_read : in std_logic;
503 trig_cnt_copy_read : in std_logic;
504 trigger_ID_ready : out std_logic;
505 trigger_ID : out std_logic_vector(55 downto 0);
506 trig_cnt_copy : out std_logic_vector(31 downto 0); --counter reading
507 trig_cnt_copy_valid : out std_logic; --trigger counter reading is valid
508 trigger_active : out std_logic; --phys triggers are enabled/active
509 config_done : out std_logic;
510 LP1_pulse : out std_logic; --send start signal to light pulser 1
511 LP2_pulse : out std_logic; --send start signal to light pulser 2
512 --trigger and time marker output signals to FADs
513 trigger_signal : out std_logic;
514 TIM_signal : out std_logic
515 );
516 end component;
517
518 component Clock_cond_interface is
519 port(
520 clk : IN STD_LOGIC;
521 CLK_Clk_Cond : out STD_LOGIC;
522 LE_Clk_Cond : out STD_LOGIC;
523 DATA_Clk_Cond : out STD_LOGIC;
524 SYNC_Clk_Cond : out STD_LOGIC;
525 LD_Clk_Cond : in STD_LOGIC;
526 TIM_Sel : out STD_LOGIC;
527 cc_R0 : in std_logic_vector (31 downto 0) := (others => '0');
528 cc_R1 : in std_logic_vector (31 downto 0) := (others => '0');
529 cc_R8 : in std_logic_vector (31 downto 0) := (others => '0');
530 cc_R9 : in std_logic_vector (31 downto 0) := (others => '0');
531 cc_R11 : in std_logic_vector (31 downto 0) := (others => '0');
532 cc_R13 : in std_logic_vector (31 downto 0) := (others => '0');
533 cc_R14 : in std_logic_vector (31 downto 0) := (others => '0');
534 cc_R15 : in std_logic_vector (31 downto 0) := (others => '0');
535 start_config : in STD_LOGIC;
536 config_started : out STD_LOGIC;
537 config_done : out STD_LOGIC;
538 locked : out STD_LOGIC;
539 timemarker_select : in STD_LOGIC
540 );
541 end component;
542
543 component FTM_central_control
544 port(
545 clk : IN std_logic;
546 clk_ready : in std_logic;
547 clk_scaler : IN std_logic;
548 new_config : IN std_logic;
549 config_started : OUT std_logic := '0';
550 config_started_ack : IN std_logic;
551 config_start_eth : OUT std_logic := '0';
552 config_started_eth : IN std_logic;
553 config_ready_eth : IN std_logic;
554 config_start_ftu : OUT std_logic := '0';
555 config_started_ftu : IN std_logic;
556 config_ready_ftu : IN std_logic;
557 ping_ftu_start : IN std_logic;
558 ping_ftu_started : OUT std_logic := '0';
559 ping_ftu_ready : OUT std_logic := '0';
560 ping_ftu_start_ftu : OUT std_logic := '0';
561 ping_ftu_started_ftu : IN std_logic;
562 ping_ftu_ready_ftu : IN std_logic;
563 rates_ftu : OUT std_logic := '0';
564 rates_started_ftu : IN std_logic;
565 rates_ready_ftu : IN std_logic;
566 prescaling_FTU01 : IN std_logic_vector(7 downto 0);
567 dd_send : OUT std_logic := '0';
568 dd_send_ack : IN std_logic;
569 dd_send_ready : IN std_logic;
570 dd_block_ready_ftu : out std_logic := '0';
571 dd_block_start_ack_ftu : in std_logic;
572 dd_block_start_ftu : out std_logic := '0';
573 config_start_cc : out std_logic := '0';
574 config_started_cc : in std_logic;
575 config_ready_cc : in std_logic;
576 cc_locked : in std_logic;
577 config_start_lp : out std_logic := '0';
578 config_started_lp : in std_logic;
579 config_ready_lp : in std_logic;
580 config_trigger : out std_logic;
581 config_trigger_done : in std_logic;
582 dna_start : out std_logic;
583 dna_ready : in std_logic;
584 crate_reset : IN std_logic;
585 crate_reset_ack : OUT std_logic;
586 crate_reset_param : IN std_logic_vector (15 DOWNTO 0);
587 start_run : IN std_logic;
588 start_run_ack : OUT std_logic;
589 stop_run : IN std_logic;
590 stop_run_ack : OUT std_logic;
591 current_cc_state : OUT std_logic_vector (15 DOWNTO 0);
592 cc_state_test : OUT std_logic_vector ( 7 downto 0);
593 start_run_param : IN std_logic_vector (15 DOWNTO 0);
594 start_run_num_events : IN std_logic_vector (31 DOWNTO 0);
595 trigger_start : out std_logic;
596 trigger_stop : out std_logic;
597 enable_ID_sending : out std_logic;
598 reset_timer : out std_logic;
599 crate_res_0 : out std_logic;
600 crate_res_1 : out std_logic;
601 crate_res_2 : out std_logic;
602 crate_res_3 : out std_logic;
603 new_config_ftu : in std_logic;
604 new_config_ftu_ack : out std_logic := '0';
605 config_single_FTU : out std_logic := '0';
606 config_single_FTU_started : in std_logic;
607 config_single_FTU_done : in std_logic
608 );
609 end component;
610
611 component FTM_ftu_control
612 port(
613 clk_50MHz : in std_logic;
614 rx_en : out STD_LOGIC;
615 tx_en : out STD_LOGIC;
616 rx_d_0 : in STD_LOGIC;
617 tx_d_0 : out STD_LOGIC;
618 rx_d_1 : in STD_LOGIC;
619 tx_d_1 : out STD_LOGIC;
620 rx_d_2 : in STD_LOGIC;
621 tx_d_2 : out STD_LOGIC;
622 rx_d_3 : in STD_LOGIC;
623 tx_d_3 : out STD_LOGIC;
624 new_config : in std_logic;
625 ping_all : in std_logic;
626 read_rates : in std_logic;
627 config_single_FTU : in std_logic;
628 read_rates_started : out std_logic := '0';
629 read_rates_done : out std_logic := '0';
630 new_config_started : out std_logic := '0';
631 new_config_done : out std_logic := '0';
632 ping_all_started : out std_logic := '0';
633 ping_all_done : out std_logic := '0';
634 config_single_FTU_started : out std_logic := '0';
635 config_single_FTU_done : out std_logic := '0';
636 ftu_active_cr0 : in std_logic_vector (15 downto 0);
637 ftu_active_cr1 : in std_logic_vector (15 downto 0);
638 ftu_active_cr2 : in std_logic_vector (15 downto 0);
639 ftu_active_cr3 : in std_logic_vector (15 downto 0);
640 config_single_FTU_param : in std_logic_vector (15 DOWNTO 0);
641 ftu_error_calls : out std_logic_vector (15 DOWNTO 0) := (others => '0');
642 ftu_error_data : out std_logic_vector ((FTU_RS485_BLOCK_WIDTH - 1) downto 0) := (others => '0');
643 ftu_error_send : out std_logic := '0';
644 ftu_error_send_ack : in std_logic;
645 ftu_error_send_ready : in std_logic;
646 static_RAM_busy : in std_logic;
647 static_RAM_started : in std_logic;
648 static_RAM_ready : in std_logic;
649 data_static_RAM : in std_logic_vector(15 downto 0) := (others => '0');
650 read_static_RAM : out std_logic := '0';
651 addr_static_RAM : out std_logic_vector(11 downto 0) := (others => '0');
652 dynamic_RAM_busy : in std_logic;
653 dynamic_RAM_started : in std_logic;
654 dynamic_RAM_ready : in std_logic;
655 data_dynamic_RAM : out std_logic_vector(15 downto 0) := (others => '0');
656 write_dynamic_RAM : out std_logic := '0';
657 addr_dynamic_RAM : out std_logic_vector(11 downto 0) := (others => '0');
658 FTUlist_RAM_busy : in std_logic;
659 FTUlist_RAM_started : in std_logic;
660 FTUlist_RAM_ready : in std_logic;
661 data_FTUlist_RAM : out std_logic_vector(15 downto 0) := (others => '0');
662 write_FTUlist_RAM : out std_logic := '0';
663 addr_FTUlist_RAM : out std_logic_vector(11 downto 0) := (others => '0')
664 );
665 end component;
666
667 component FTM_fad_broadcast
668 port(
669 clk_50MHz : in std_logic;
670 rx_en : out STD_LOGIC;
671 tx_en : out STD_LOGIC;
672 rx_d_0 : in STD_LOGIC;
673 tx_d_0 : out STD_LOGIC;
674 rx_d_1 : in STD_LOGIC;
675 tx_d_1 : out STD_LOGIC;
676 rx_d_2 : in STD_LOGIC;
677 tx_d_2 : out STD_LOGIC;
678 rx_d_3 : in STD_LOGIC;
679 tx_d_3 : out STD_LOGIC;
680 enable_ID_sending : in std_logic;
681 TIM_source : in std_logic;
682 LP_settings : in std_logic_vector(3 downto 0);
683 trigger_ID_ready : in std_logic;
684 trigger_ID : in std_logic_vector(FAD_RS485_BLOCK_WIDTH - 1 downto 0);
685 trigger_ID_read : out std_logic
686 );
687 end component;
688
689 component ethernet_modul
690 port(
691 wiz_reset : OUT std_logic := '1';
692 wiz_addr : OUT std_logic_vector (9 DOWNTO 0);
693 wiz_data : INOUT std_logic_vector (15 DOWNTO 0);
694 wiz_cs : OUT std_logic := '1';
695 wiz_wr : OUT std_logic := '1';
696 wiz_rd : OUT std_logic := '1';
697 wiz_int : IN std_logic ;
698 clk : IN std_logic ;
699 sd_ready : OUT std_logic ;
700 sd_busy : OUT std_logic ;
701 led : OUT std_logic_vector (7 DOWNTO 0);
702 sd_read_ftu : IN std_logic ;
703 sd_started_ftu : OUT std_logic := '0';
704 cc_R0 : OUT std_logic_vector (31 DOWNTO 0);
705 cc_R1 : OUT std_logic_vector (31 DOWNTO 0);
706 cc_R11 : OUT std_logic_vector (31 DOWNTO 0);
707 cc_R13 : OUT std_logic_vector (31 DOWNTO 0);
708 cc_R14 : OUT std_logic_vector (31 DOWNTO 0);
709 cc_R15 : OUT std_logic_vector (31 DOWNTO 0);
710 cc_R8 : OUT std_logic_vector (31 DOWNTO 0);
711 cc_R9 : OUT std_logic_vector (31 DOWNTO 0);
712 coin_n_c : OUT std_logic_vector (15 DOWNTO 0);
713 coin_n_p : OUT std_logic_vector (15 DOWNTO 0);
714 dead_time : OUT std_logic_vector (15 DOWNTO 0);
715 general_settings : OUT std_logic_vector (15 DOWNTO 0);
716 lp1_amplitude : OUT std_logic_vector (15 DOWNTO 0);
717 lp1_delay : OUT std_logic_vector (15 DOWNTO 0);
718 lp2_amplitude : OUT std_logic_vector (15 DOWNTO 0);
719 lp2_delay : OUT std_logic_vector (15 DOWNTO 0);
720 lp_pt_freq : OUT std_logic_vector (15 DOWNTO 0);
721 lp_pt_ratio : OUT std_logic_vector (15 DOWNTO 0);
722 timemarker_delay : OUT std_logic_vector (15 DOWNTO 0);
723 trigger_delay : OUT std_logic_vector (15 DOWNTO 0);
724 sd_addr_ftu : IN std_logic_vector (11 DOWNTO 0);
725 sd_data_out_ftu : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
726 ftu_active_cr0 : OUT std_logic_vector (15 DOWNTO 0);
727 ftu_active_cr1 : OUT std_logic_vector (15 DOWNTO 0);
728 ftu_active_cr2 : OUT std_logic_vector (15 DOWNTO 0);
729 ftu_active_cr3 : OUT std_logic_vector (15 DOWNTO 0);
730 new_config : OUT std_logic := '0';
731 config_started : IN std_logic ;
732 config_start_eth : IN std_logic ;
733 config_started_eth : OUT std_logic := '0';
734 config_ready_eth : OUT std_logic := '0';
735 config_started_ack : OUT std_logic := '0';
736 fl_busy : OUT std_logic ;
737 fl_ready : OUT std_logic ;
738 fl_write_ftu : IN std_logic ;
739 fl_started_ftu : OUT std_logic := '0';
740 fl_addr_ftu : IN std_logic_vector (11 DOWNTO 0);
741 fl_data_in_ftu : IN std_logic_vector (15 DOWNTO 0) := (others => '0');
742 ping_ftu_start : OUT std_logic := '0';
743 ping_ftu_started : IN std_logic ;
744 ping_ftu_ready : IN std_logic ;
745 dd_write_ftu : IN std_logic ;
746 dd_started_ftu : OUT std_logic := '0';
747 dd_data_in_ftu : IN std_logic_vector (15 DOWNTO 0);
748 dd_addr_ftu : IN std_logic_vector (11 DOWNTO 0);
749 dd_busy : OUT std_logic ;
750 dd_ready : OUT std_logic ;
751 coin_win_c : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
752 coin_win_p : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
753 --new stuff
754 dd_block_ready_ftu : IN std_logic;
755 dd_block_start_ack_ftu : OUT std_logic := '0';
756 dd_block_start_ftu : IN std_logic;
757 dd_send : IN std_logic;
758 dd_send_ack : OUT std_logic := '1';
759 dd_send_ready : OUT std_logic := '1';
760 --very new stuff
761 ftu_error_calls : IN std_logic_vector (15 DOWNTO 0);
762 ftu_error_data : IN std_logic_vector (223 DOWNTO 0); -- (28 * 8) - 1
763 ftu_error_send : IN std_logic;
764 ftu_error_send_ack : OUT std_logic := '1';
765 ftu_error_send_ready : OUT std_logic := '1';
766 prescaling_FTU01 : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
767 trigger_counter : IN std_logic_vector (31 DOWNTO 0) := (others => '0');
768 trigger_counter_read : OUT std_logic := '0';
769 trigger_counter_valid : IN std_logic;
770 --newest stuff
771 board_id : IN std_logic_vector (63 DOWNTO 0);
772 get_ts_counter : OUT std_logic := '0';
773 get_ts_counter_ready : IN std_logic;
774 get_ts_counter_started : IN std_logic;
775 timestamp_counter : IN std_logic_vector (47 DOWNTO 0);
776 get_ot_counter : OUT std_logic := '0';
777 get_ot_counter_ready : IN std_logic;
778 get_ot_counter_started : IN std_logic;
779 on_time_counter : IN std_logic_vector (47 DOWNTO 0);
780 temp_sensor_array : IN sensor_array_type;
781 temp_sensor_ready : IN std_logic;
782 crate_reset : OUT std_logic := '0';
783 crate_reset_ack : IN std_logic;
784 crate_reset_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
785 start_run : OUT std_logic := '0';
786 start_run_ack : IN std_logic;
787 stop_run : OUT std_logic := '0';
788 stop_run_ack : IN std_logic;
789 current_cc_state : IN std_logic_vector (15 DOWNTO 0);
790 start_run_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0');
791 start_run_num_events : OUT std_logic_vector (31 DOWNTO 0) := (others => '0');
792 new_config_ftu : OUT std_logic := '0';
793 new_config_ftu_ack : IN std_logic;
794 new_config_ftu_param : OUT std_logic_vector (15 DOWNTO 0) := (others => '0')
795 );
796 end component;
797
798-- component counter_dummy IS
799-- PORT(
800-- clk : IN std_logic;
801-- get_counter : IN std_logic;
802-- get_counter_started : OUT std_logic := '0';
803-- get_counter_ready : OUT std_logic := '0';
804-- counter : OUT std_logic_vector (47 DOWNTO 0) := (others => '0')
805-- );
806-- end component;
807
808 component Timing_counter is
809 port(
810 clk : in STD_LOGIC; -- 50 MHz system clock
811 enable : in STD_LOGIC; -- enable counter
812 reset : in Std_LOGIC; -- reset counter
813 read_counter : in STD_LOGIC; -- read counter
814 reading_started : out STD_LOGIC;
815 reading_valid : out STD_LOGIC; -- counter reading at output ready
816 counter_reading : out std_logic_vector (TC_WIDTH - 1 downto 0)
817 );
818 end component;
819
820 component Lightpulser_interface_Basic is
821 port(
822 clk_50 : IN STD_LOGIC;
823 --clk_250 : IN STD_LOGIC;
824 Cal_0_p : out STD_LOGIC := '0';
825 Cal_0_n : out STD_LOGIC := '1';
826 Cal_1_p : out STD_LOGIC := '0';
827 Cal_1_n : out STD_LOGIC := '1';
828 Cal_2_p : out STD_LOGIC := '0';
829 Cal_2_n : out STD_LOGIC := '1';
830 Cal_3_p : out STD_LOGIC := '0';
831 Cal_3_n : out STD_LOGIC := '1';
832 Cal_4_p : out STD_LOGIC := '0';
833 Cal_4_n : out STD_LOGIC := '1';
834 Cal_5_p : out STD_LOGIC := '0';
835 Cal_5_n : out STD_LOGIC := '1';
836 Cal_6_p : out STD_LOGIC := '0';
837 Cal_6_n : out STD_LOGIC := '1';
838 Cal_7_p : out STD_LOGIC := '0';
839 Cal_7_n : out STD_LOGIC := '1';
840 LP1_ampl : in std_logic_vector (15 downto 0);
841 LP2_ampl : in std_logic_vector (15 downto 0);
842 --LP1_delay : in std_logic_vector (15 downto 0);
843 --LP2_delay : in std_logic_vector (15 downto 0);
844 LP1_pulse : in std_logic;
845 LP2_pulse : in std_logic;
846 start_config : in std_logic;
847 config_started : out std_logic := '0';
848 config_done : out std_logic := '0'
849 );
850 end component;
851
852begin
853
854-- -- IBUFG: Single-ended global clock input buffer
855-- -- Spartan-3A
856-- -- Xilinx HDL Language Template, version 11.4
857
858-- IBUFG_inst : IBUFG
859-- generic map (
860-- IBUF_DELAY_VALUE => "0", -- Specify the amount of added input delay for buffer,
861-- -- "0"-"16"
862-- IOSTANDARD => "DEFAULT")
863-- port map (
864-- O => clk_buf_sig, -- Clock buffer output
865-- I => clk -- Clock buffer input (connect directly to top-level port)
866-- );
867
868-- Inst_FTM_clk_gen : FTM_clk_gen
869-- port map(
870-- clk => clk_buf_sig,
871-- rst => reset_sig,
872-- clk_1 => clk_1M_sig,
873-- clk_50 => clk_50M_sig,
874-- clk_250 => clk_250M_sig,
875-- clk_250_ps => clk_250M_ps_sig,
876-- ready => clk_ready_sig
877-- );
878
879 Inst_FTM_clk_gen_2 : FTM_clk_gen_2
880 port map(
881 clk => clk,
882 rst => reset_sig,
883 clk_1 => clk_1M_sig,
884 clk_50 => clk_50M_sig,
885 clk_250 => clk_250M_sig,
886 clk_250_ps => clk_250M_ps_sig,
887 ready => clk_ready_sig
888 );
889
890 Inst_FTM_dna_gen : FTM_dna_gen
891 port map(
892 clk => clk_50M_sig,
893 start => dna_start_sig,
894 dna => dna_sig,
895 ready => dna_ready_sig
896 );
897
898 --differential output buffer for trigger signal
899 OBUFDS_LVDS_33_TRG : OBUFDS_LVDS_33
900 port map(
901 O => TRG_p,
902 OB => TRG_n,
903 I => trigger_signal_sig
904 );
905
906 --differential output buffer for TIM signal
907 OBUFDS_LVDS_33_TIM : OBUFDS_LVDS_33
908 port map(
909 O => TIM_Run_p,
910 OB => TIM_Run_n,
911 I => TIM_signal_sig
912 );
913
914 --differential output buffer for fast reset signal
915 OBUFDS_LVDS_33_RES : OBUFDS_LVDS_33
916 port map(
917 O => RES_p,
918 OB => RES_n,
919 I => '0'
920 );
921
922 Inst_trigger_manager : trigger_manager
923 port map(
924 --clocks
925 clk_50MHz => clk_50M_sig,
926 clk_250MHz => clk_250M_sig,
927 clk_250MHz_180 => clk_250M_ps_sig,
928 --trigger primitives from FTUs
929 trig_prim_0 => Trig_Prim_A, --crate 0
930 trig_prim_1 => Trig_Prim_B, --crate 1
931 trig_prim_2 => Trig_Prim_C, --crate 2
932 trig_prim_3 => Trig_Prim_D, --crate 3
933 --external signals
934 ext_trig_1 => ext_Trig(1),
935 ext_trig_2 => ext_Trig(2),
936 ext_veto => Veto,
937 FAD_busy_0 => Busy0, --crate 0
938 FAD_busy_1 => Busy1, --crate 1
939 FAD_busy_2 => Busy2, --crate 2
940 FAD_busy_3 => Busy3, --crate 3
941 --control signals from e.g. main control
942 start_run => trigger_start_sig, --enable trigger output
943 stop_run => trigger_stop_sig, --disable trigger output
944 new_config => config_trigger_sig,
945 --settings register (see FTM Firmware Specifications)
946 general_settings => general_settings_sig,
947 LP_and_PED_freq => lp_pt_freq_sig,
948 LP1_LP2_PED_ratio => lp_pt_ratio_sig,
949 maj_coinc_n_phys => coin_n_p_sig,
950 maj_coinc_n_calib => coin_n_c_sig,
951 trigger_delay => trigger_delay_sig,
952 TIM_delay => timemarker_delay_sig,
953 dead_time => dead_time_sig,
954 coinc_window_phys => coin_win_p_sig,
955 coinc_window_calib => coin_win_c_sig,
956 active_FTU_list_0 => ftu_active_cr0_sig,
957 active_FTU_list_1 => ftu_active_cr1_sig,
958 active_FTU_list_2 => ftu_active_cr2_sig,
959 active_FTU_list_3 => ftu_active_cr3_sig,
960 --control signals or information for other entities
961 trigger_ID_read => trigger_ID_read_sig,
962 trig_cnt_copy_read => trigger_counter_read_sig,
963 trigger_ID_ready => trigger_ID_ready_sig,
964 trigger_ID => trigger_ID_sig,
965 trig_cnt_copy => trigger_counter_sig, --counter reading
966 trig_cnt_copy_valid => trigger_counter_valid_sig, --trigger counter reading is valid
967 trigger_active => trigger_active_sig, --phys triggers are enabled/active
968 config_done => config_trigger_done_sig,
969 LP1_pulse => LP1_pulse_sig, --send start signal to light pulser 1
970 LP2_pulse => LP2_pulse_sig, --send start signal to light pulser 2
971 --trigger and time marker output signals to FADs
972 trigger_signal => trigger_signal_sig,
973 TIM_signal => TIM_signal_sig
974 );
975
976 Inst_Clock_cond_interface : Clock_cond_interface
977 port map(
978 clk => clk_50M_sig,
979 CLK_Clk_Cond => CLK_Clk_Cond,
980 LE_Clk_Cond => LE_Clk_Cond,
981 DATA_Clk_Cond => DATA_Clk_Cond,
982 SYNC_Clk_Cond => SYNC_Clk_Cond,
983 LD_Clk_Cond => LD_Clk_Cond,
984 TIM_Sel => TIM_Sel,
985 cc_R0 => cc_R0_sig,
986 cc_R1 => cc_R1_sig,
987 cc_R8 => cc_R8_sig,
988 cc_R9 => cc_R9_sig,
989 cc_R11 => cc_R11_sig,
990 cc_R13 => cc_R13_sig,
991 cc_R14 => cc_R14_sig,
992 cc_R15 => cc_R15_sig,
993 start_config => config_start_cc_sig,
994 config_started => config_started_cc_sig,
995 config_done => config_ready_cc_sig,
996 locked => cc_locked_sig,
997 timemarker_select => general_settings_sig(0)
998 );
999
1000 Inst_FTM_central_control : FTM_central_control
1001 port map(
1002 clk => clk_50M_sig,
1003 clk_ready => clk_ready_sig,
1004 clk_scaler => clk_1M_sig,
1005 new_config => new_config_sig,
1006 config_started => config_started_sig,
1007 config_started_ack => config_started_ack_sig,
1008 config_start_eth => config_start_eth_sig,
1009 config_started_eth => config_started_eth_sig,
1010 config_ready_eth => config_ready_eth_sig,
1011 config_start_ftu => config_start_ftu_sig,
1012 config_started_ftu => config_started_ftu_sig,
1013 config_ready_ftu => config_ready_ftu_sig,
1014 ping_ftu_start => ping_ftu_start_sig,
1015 ping_ftu_started => ping_ftu_started_sig,
1016 ping_ftu_ready => ping_ftu_ready_sig,
1017 ping_ftu_start_ftu => ping_ftu_start_ftu_sig,
1018 ping_ftu_started_ftu => ping_ftu_started1_sig,
1019 ping_ftu_ready_ftu => ping_ftu_ready1_sig,
1020 rates_ftu => rates_ftu_start_sig,
1021 rates_started_ftu => rates_ftu_started_sig,
1022 rates_ready_ftu => rates_ftu_ready_sig,
1023 prescaling_FTU01 => prescaling_FTU01_sig(7 downto 0),
1024 dd_send => dd_send_sig,
1025 dd_send_ack => dd_send_ack_sig,
1026 dd_send_ready => dd_send_ready_sig,
1027 dd_block_ready_ftu => dd_block_ready_ftu_sig,
1028 dd_block_start_ack_ftu => dd_block_start_ack_ftu_sig,
1029 dd_block_start_ftu => dd_block_start_ftu_sig,
1030 config_start_cc => config_start_cc_sig,
1031 config_started_cc => config_started_cc_sig,
1032 config_ready_cc => config_ready_cc_sig,
1033 cc_locked => cc_locked_sig,
1034 config_start_lp => config_start_lp_sig,
1035 config_started_lp => config_started_lp_sig,
1036 config_ready_lp => config_ready_lp_sig,
1037 config_trigger => config_trigger_sig,
1038 config_trigger_done => config_trigger_done_sig,
1039 dna_start => dna_start_sig,
1040 dna_ready => dna_ready_sig,
1041 crate_reset => crate_reset_sig,
1042 crate_reset_ack => crate_reset_ack_sig,
1043 crate_reset_param => crate_reset_param_sig,
1044 start_run => start_run_sig,
1045 start_run_ack => start_run_ack_sig,
1046 stop_run => stop_run_sig,
1047 stop_run_ack => stop_run_ack_sig,
1048 current_cc_state => current_cc_state_sig,
1049 cc_state_test => cc_state_test_sig,
1050 start_run_param => start_run_param_sig,
1051 start_run_num_events => start_run_num_events_sig,
1052 trigger_start => trigger_start_sig,
1053 trigger_stop => trigger_stop_sig,
1054 enable_ID_sending => enable_ID_sending_sig,
1055 reset_timer => reset_timer_sig,
1056 crate_res_0 => crate_res0_sig,
1057 crate_res_1 => crate_res1_sig,
1058 crate_res_2 => crate_res2_sig,
1059 crate_res_3 => crate_res3_sig,
1060 new_config_ftu => new_config_ftu_sig,
1061 new_config_ftu_ack => new_config_ftu_ack_sig,
1062 config_single_FTU => config_single_FTU_sig,
1063 config_single_FTU_started => config_single_FTU_started_sig,
1064 config_single_FTU_done => config_single_FTU_done_sig
1065 );
1066
1067 Inst_FTM_ftu_control : FTM_ftu_control
1068 port map(
1069 clk_50MHz => clk_50M_sig,
1070 rx_en => Bus1_Rx_En,
1071 tx_en => Bus1_Tx_En,
1072 rx_d_0 => Bus1_RxD_0,
1073 tx_d_0 => Bus1_TxD_0,
1074 rx_d_1 => Bus1_RxD_1,
1075 tx_d_1 => Bus1_TxD_1,
1076 rx_d_2 => Bus1_RxD_2,
1077 tx_d_2 => Bus1_TxD_2,
1078 rx_d_3 => Bus1_RxD_3,
1079 tx_d_3 => Bus1_TxD_3,
1080 new_config => config_start_ftu_sig,
1081 ping_all => ping_ftu_start_ftu_sig,
1082 read_rates => rates_ftu_start_sig,
1083 config_single_FTU => config_single_FTU_sig,
1084 read_rates_started => rates_ftu_started_sig,
1085 read_rates_done => rates_ftu_ready_sig,
1086 new_config_started => config_started_ftu_sig,
1087 new_config_done => config_ready_ftu_sig,
1088 ping_all_started => ping_ftu_started1_sig,
1089 ping_all_done => ping_ftu_ready1_sig,
1090 config_single_FTU_started => config_single_FTU_started_sig,
1091 config_single_FTU_done => config_single_FTU_done_sig,
1092 ftu_active_cr0 => ftu_active_cr0_sig,
1093 ftu_active_cr1 => ftu_active_cr1_sig,
1094 ftu_active_cr2 => ftu_active_cr2_sig,
1095 ftu_active_cr3 => ftu_active_cr3_sig,
1096 config_single_FTU_param => new_config_ftu_param_sig,
1097 ftu_error_calls => ftu_error_calls_sig,
1098 ftu_error_data => ftu_error_data_sig,
1099 ftu_error_send => ftu_error_send_sig,
1100 ftu_error_send_ack => ftu_error_send_ack_sig,
1101 ftu_error_send_ready=> ftu_error_send_ready_sig,
1102 static_RAM_busy => sd_busy_sig,
1103 static_RAM_started => sd_started_ftu_sig,
1104 static_RAM_ready => sd_ready_sig,
1105 data_static_RAM => sd_data_out_ftu_sig,
1106 read_static_RAM => sd_read_ftu_sig,
1107 addr_static_RAM => sd_addr_ftu_sig,
1108 dynamic_RAM_busy => dd_busy_sig,
1109 dynamic_RAM_started => dd_started_ftu_sig,
1110 dynamic_RAM_ready => dd_ready_sig,
1111 data_dynamic_RAM => dd_data_sig,
1112 write_dynamic_RAM => dd_write_sig,
1113 addr_dynamic_RAM => dd_addr_sig,
1114 FTUlist_RAM_busy => fl_busy_sig,
1115 FTUlist_RAM_started => fl_started_ftu_sig,
1116 FTUlist_RAM_ready => fl_ready_sig,
1117 data_FTUlist_RAM => fl_data_sig,
1118 write_FTUlist_RAM => fl_write_sig,
1119 addr_FTUlist_RAM => fl_addr_sig
1120 );
1121
1122 Inst_FTM_fad_broadcast : FTM_fad_broadcast
1123 port map(
1124 clk_50MHz => clk_50M_sig,
1125 rx_en => Bus2_Rx_En,
1126 tx_en => Bus2_Tx_En,
1127 rx_d_0 => Bus2_RxD_0,
1128 tx_d_0 => Bus2_TxD_0,
1129 rx_d_1 => Bus2_RxD_1,
1130 tx_d_1 => Bus2_TxD_1,
1131 rx_d_2 => Bus2_RxD_2,
1132 tx_d_2 => Bus2_TxD_2,
1133 rx_d_3 => Bus2_RxD_3,
1134 tx_d_3 => Bus2_TxD_3,
1135 enable_ID_sending => enable_ID_sending_sig,
1136 TIM_source => general_settings_sig(0),
1137 LP_settings => "0000",
1138 trigger_ID_ready => trigger_ID_ready_sig,
1139 trigger_ID => trigger_ID_sig,
1140 trigger_ID_read => trigger_ID_read_sig
1141 );
1142
1143 Inst_ethernet_modul : ethernet_modul
1144 port map(
1145 wiz_reset => W_RES,
1146 wiz_addr => W_A,
1147 wiz_data => W_D,
1148 wiz_cs => W_CS,
1149 wiz_wr => W_WR,
1150 wiz_rd => W_RD,
1151 wiz_int => W_INT,
1152 clk => clk_50M_sig,
1153 sd_ready => sd_ready_sig,
1154 sd_busy => sd_busy_sig,
1155 led => led_sig,
1156 sd_read_ftu => sd_read_ftu_sig,
1157 sd_started_ftu => sd_started_ftu_sig,
1158 cc_R0 => cc_R0_sig,
1159 cc_R1 => cc_R1_sig,
1160 cc_R11 => cc_R11_sig,
1161 cc_R13 => cc_R13_sig,
1162 cc_R14 => cc_R14_sig,
1163 cc_R15 => cc_R15_sig,
1164 cc_R8 => cc_R8_sig,
1165 cc_R9 => cc_R9_sig,
1166 coin_n_c => coin_n_c_sig,
1167 coin_n_p => coin_n_p_sig,
1168 dead_time => dead_time_sig,
1169 general_settings => general_settings_sig,
1170 lp1_amplitude => lp1_amplitude_sig,
1171 lp1_delay => lp1_delay_sig,
1172 lp2_amplitude => lp2_amplitude_sig,
1173 lp2_delay => lp2_delay_sig,
1174 lp_pt_freq => lp_pt_freq_sig,
1175 lp_pt_ratio => lp_pt_ratio_sig,
1176 timemarker_delay => timemarker_delay_sig,
1177 trigger_delay => trigger_delay_sig,
1178 sd_addr_ftu => sd_addr_ftu_sig,
1179 sd_data_out_ftu => sd_data_out_ftu_sig,
1180 ftu_active_cr0 => ftu_active_cr0_sig,
1181 ftu_active_cr1 => ftu_active_cr1_sig,
1182 ftu_active_cr2 => ftu_active_cr2_sig,
1183 ftu_active_cr3 => ftu_active_cr3_sig,
1184 new_config => new_config_sig,
1185 config_started => config_started_sig,
1186 config_start_eth => config_start_eth_sig,
1187 config_started_eth => config_started_eth_sig,
1188 config_ready_eth => config_ready_eth_sig,
1189 config_started_ack => config_started_ack_sig,
1190 fl_busy => fl_busy_sig,
1191 fl_ready => fl_ready_sig,
1192 fl_write_ftu => fl_write_sig,
1193 fl_started_ftu => fl_started_ftu_sig,
1194 fl_addr_ftu => fl_addr_sig,
1195 fl_data_in_ftu => fl_data_sig,
1196 ping_ftu_start => ping_ftu_start_sig,
1197 ping_ftu_started => ping_ftu_started_sig,
1198 ping_ftu_ready => ping_ftu_ready_sig,
1199 dd_write_ftu => dd_write_sig,
1200 dd_started_ftu => dd_started_ftu_sig,
1201 dd_data_in_ftu => dd_data_sig,
1202 dd_addr_ftu => dd_addr_sig,
1203 dd_busy => dd_busy_sig,
1204 dd_ready => dd_ready_sig,
1205 coin_win_c => coin_win_c_sig,
1206 coin_win_p => coin_win_p_sig,
1207 --new stuff
1208 dd_block_ready_ftu => dd_block_ready_ftu_sig,
1209 dd_block_start_ack_ftu => dd_block_start_ack_ftu_sig,
1210 dd_block_start_ftu => dd_block_start_ftu_sig,
1211 dd_send => dd_send_sig,
1212 dd_send_ack => dd_send_ack_sig,
1213 dd_send_ready => dd_send_ready_sig,
1214 --very new stuff
1215 ftu_error_calls => ftu_error_calls_sig,
1216 ftu_error_data => ftu_error_data_sig,
1217 ftu_error_send => ftu_error_send_sig,
1218 ftu_error_send_ack => ftu_error_send_ack_sig,
1219 ftu_error_send_ready => ftu_error_send_ready_sig,
1220 prescaling_FTU01 => prescaling_FTU01_sig,
1221 trigger_counter => trigger_counter_sig,
1222 trigger_counter_read => trigger_counter_read_sig,
1223 trigger_counter_valid => trigger_counter_valid_sig,
1224 --newest stuff
1225 board_id => dna_sig,
1226 get_ts_counter => get_ts_counter_sig,
1227 get_ts_counter_ready => get_ts_counter_ready_sig,
1228 get_ts_counter_started => get_ts_counter_started_sig,
1229 timestamp_counter => timestamp_counter_sig,
1230 get_ot_counter => get_ot_counter_sig,
1231 get_ot_counter_ready => get_ot_counter_ready_sig,
1232 get_ot_counter_started => get_ot_counter_started_sig,
1233 on_time_counter => on_time_counter_sig,
1234 temp_sensor_array => (35, 45, 55, 65),
1235 temp_sensor_ready => '1',
1236 crate_reset => crate_reset_sig,
1237 crate_reset_ack => crate_reset_ack_sig,
1238 crate_reset_param => crate_reset_param_sig,
1239 start_run => start_run_sig,
1240 start_run_ack => start_run_ack_sig,
1241 stop_run => stop_run_sig,
1242 stop_run_ack => stop_run_ack_sig,
1243 current_cc_state => current_cc_state_sig,
1244 start_run_param => start_run_param_sig,
1245 start_run_num_events => start_run_num_events_sig,
1246 new_config_ftu => new_config_ftu_sig,
1247 new_config_ftu_ack => new_config_ftu_ack_sig,
1248 new_config_ftu_param => new_config_ftu_param_sig
1249 );
1250
1251-- Inst_counter_dummy_ts : counter_dummy
1252-- port map(
1253-- clk => clk_50M_sig,
1254-- get_counter => get_ts_counter_sig,
1255-- get_counter_started => get_ts_counter_started_sig,
1256-- get_counter_ready => get_ts_counter_ready_sig,
1257-- counter => timestamp_counter_sig
1258-- );
1259
1260-- Inst_counter_dummy_ot : counter_dummy
1261-- port map(
1262-- clk => clk_50M_sig,
1263-- get_counter => get_ot_counter_sig,
1264-- get_counter_started => get_ot_counter_started_sig,
1265-- get_counter_ready => get_ot_counter_ready_sig,
1266-- counter => on_time_counter_sig
1267-- );
1268
1269 Inst_Timing_counter_ts : Timing_counter
1270 port map(
1271 clk => clk_50M_sig,
1272 enable => '1',
1273 reset => reset_timer_sig,
1274 read_counter => get_ts_counter_sig,
1275 reading_started => get_ts_counter_started_sig,
1276 reading_valid => get_ts_counter_ready_sig,
1277 counter_reading => timestamp_counter_sig
1278 );
1279
1280 Inst_Timing_counter_ot : Timing_counter
1281 port map(
1282 clk => clk_50M_sig,
1283 enable => trigger_active_sig,
1284 reset => reset_timer_sig,
1285 read_counter => get_ot_counter_sig,
1286 reading_started => get_ot_counter_started_sig,
1287 reading_valid => get_ot_counter_ready_sig,
1288 counter_reading => on_time_counter_sig
1289 );
1290
1291 Inst_Lightpulser_interface_Basic : Lightpulser_interface_Basic
1292 port map (
1293 clk_50 => clk_50M_sig,
1294 --clk_250 => clk_250M_sig,
1295 Cal_0_p => Cal_2_p, --swapped with Cal_2_p due to connector on FLD board
1296 Cal_0_n => Cal_2_n, --swapped with Cal_2_n due to connector on FLD board
1297 Cal_1_p => Cal_1_p,
1298 Cal_1_n => Cal_1_n,
1299 Cal_2_p => Cal_0_p, --swapped with Cal_0_p due to connector on FLD board
1300 Cal_2_n => Cal_0_n, --swapped with Cal_0_n due to connector on FLD board
1301 Cal_3_p => Cal_3_p,
1302 Cal_3_n => Cal_3_n,
1303 Cal_4_p => Cal_6_p, --swapped with Cal_6_p due to connector on FLD board
1304 Cal_4_n => Cal_6_n, --swapped with Cal_6_n due to connector on FLD board
1305 Cal_5_p => Cal_5_p,
1306 Cal_5_n => Cal_5_n,
1307 Cal_6_p => Cal_4_p, --swapped with Cal_4_p due to connector on FLD board
1308 Cal_6_n => Cal_4_n, --swapped with Cal_4_n due to connector on FLD board
1309 Cal_7_p => Cal_7_p,
1310 Cal_7_n => Cal_7_n,
1311 LP1_ampl => lp1_amplitude_sig,
1312 LP2_ampl => lp2_amplitude_sig,
1313 --LP1_delay => lp1_delay_sig,
1314 --LP2_delay => lp2_delay_sig,
1315 LP1_pulse => LP1_pulse_sig,
1316 LP2_pulse => LP2_pulse_sig,
1317 start_config => config_start_lp_sig,
1318 config_started => config_started_lp_sig,
1319 config_done => config_ready_lp_sig
1320 );
1321
1322 --LED_red <= led_sig(3 downto 0);
1323 --LED_ye <= led_sig(5 downto 4);
1324 --LED_gn <= led_sig(7 downto 6);
1325 LED_red <= "1111";
1326 LED_ye <= "11";
1327 LED_gn <= "11";
1328
1329 TP(32 downto 8) <= (others => '0');
1330 --TP(8) <= clk_50M_sig;
1331 TP( 7 downto 0) <= cc_state_test_sig;
1332
1333 Crate_Res0 <= crate_res0_sig;
1334 Crate_Res1 <= crate_res1_sig;
1335 Crate_Res2 <= crate_res2_sig;
1336 Crate_Res3 <= crate_res3_sig;
1337
1338end Behavioral;
1339
1340
Note: See TracBrowser for help on using the repository browser.