-------------------------------------------------------------------------------- -- Company: ETH Zurich, Institute for Particle Physics -- Engineer: Q. Weitzel, P. Vogler -- -- Create Date: 08.12.2010 -- Design Name: -- Module Name: FTM_top_tb.vhd -- Project Name: -- Target Device: -- Tool versions: -- Description: Testbench for FTM firmware -- -- VHDL Test Bench Created by ISE for module: FTM_top -- -- Dependencies: -- -- Revision: -- Revision 0.01 - File Created -- Additional Comments: -- -- Notes: -- This testbench has been automatically generated using types std_logic and -- std_logic_vector for the ports of the unit under test. Xilinx recommends -- that these types always be used for the top-level I/O of a design in order -- to guarantee that the testbench will bind correctly to the post-implementation -- simulation model. -------------------------------------------------------------------------------- library IEEE; use IEEE.STD_LOGIC_1164.ALL; use IEEE.STD_LOGIC_UNSIGNED.ALL; use IEEE.NUMERIC_STD.ALL; library UNISIM; use UNISIM.VComponents.all; entity FTM_top_tb is end FTM_top_tb; architecture behavior of FTM_top_tb is -- Component Declaration for the Unit Under Test (UUT) component FTM_top port( -- Clock clk : IN STD_LOGIC; -- external clock from oscillator U47 -- connection to the WIZnet W5300 ethernet controller ------------------------------------------------------------------------------- -- W5300 data bus W_D : inout STD_LOGIC_VECTOR(15 downto 0); -- 16-bit data bus to W5300 -- W5300 address bus W_A : out STD_LOGIC_VECTOR(9 downto 0); -- there is no real net W_A0 because -- the W5300 is operated in the -- 16-bit mode -- -> W_A<0> assigned to unconnected pin -- W5300 control signals -- the signals W_INT, W_RD, W_WR and W_RES also go to testpoints T17 -- W_CS is also routed to testpoint JP7 W_CS : out STD_LOGIC; -- W5300 chip select W_INT : IN STD_LOGIC; -- interrupt W_RD : out STD_LOGIC; -- read W_WR : out STD_LOGIC; -- write W_RES : out STD_LOGIC; -- reset W5300 chip -- W5300 buffer ready indicator -- W_BRDY : in STD_LOGIC_VECTOR(3 downto 0); -- testpoints (T18) associated with the W5300 -- W_T : inout STD_LOGIC_VECTOR(3 downto 0); -- SPI Interface -- connection to the EEPROM U36 (AL25L016M) and -- temperature sensors U45, U46, U48 and U49 (all MAX6662) ------------------------------------------------------------------------------- -- S_CLK : out STD_LOGIC; -- SPI clock -- EEPROM -- MOSI : out STD_LOGIC; -- master out slave in -- MISO : in STD_LOGIC; -- master in slave out -- EE_CS : out STD_LOGIC; -- EEPROM chip select -- temperature sensors U45, U46, U48 and U49 -- SIO : inout STD_LOGIC; -- serial IO -- TS_CS : out STD_LOGIC_VECTOR(3 downto 0); -- temperature sensors chip select -- Trigger primitives inputs ------------------------------------------------------------------------------- Trig_Prim_A : in STD_LOGIC_VECTOR(9 downto 0); -- crate 0 Trig_Prim_B : in STD_LOGIC_VECTOR(9 downto 0); -- crate 1 Trig_Prim_C : in STD_LOGIC_VECTOR(9 downto 0); -- crate 2 Trig_Prim_D : in STD_LOGIC_VECTOR(9 downto 0); -- crate 3 -- NIM inputs ------------------------------------------------------------------------------ ext_Trig : in STD_LOGIC_VECTOR(2 downto 1); -- external trigger input Veto : in STD_LOGIC; -- trigger veto input -- NIM_In : in STD_LOGIC_VECTOR(2 downto 0); -- auxiliary inputs -- alternative external clock input for FPGA -- NIM_In3_GCLK : in STD_LOGIC; -- input with global clock buffer available -- LEDs ------------------------------------------------------------------------------- LED_red : out STD_LOGIC_VECTOR(3 downto 0); -- red LED_ye : out STD_LOGIC_VECTOR(1 downto 0); -- yellow LED_gn : out STD_LOGIC_VECTOR(1 downto 0); -- green -- Clock conditioner LMK03000 ------------------------------------------------------------------------------- CLK_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface serial clock LE_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface latch enable DATA_Clk_Cond : out STD_LOGIC; -- MICROWIRE interface data SYNC_Clk_Cond : out STD_LOGIC; -- global clock synchronization LD_Clk_Cond : in STD_LOGIC; -- lock detect, should be checked for -- various RS-485 Interfaces ------------------------------------------------------------------------------- -- Bus 1: FTU slow control Bus1_Tx_En : out STD_LOGIC; -- bus 1: transmitter enable Bus1_Rx_En : out STD_LOGIC; -- bus 1: receiver enable Bus1_RxD_0 : in STD_LOGIC; -- crate 0 Bus1_TxD_0 : out STD_LOGIC; Bus1_RxD_1 : in STD_LOGIC; -- crate 1 Bus1_TxD_1 : out STD_LOGIC; Bus1_RxD_2 : in STD_LOGIC; -- crate 2 Bus1_TxD_2 : out STD_LOGIC; Bus1_RxD_3 : in STD_LOGIC; -- crate 3 Bus1_TxD_3 : out STD_LOGIC; -- Bus 2: Trigger-ID to FAD boards Bus2_Tx_En : out STD_LOGIC; -- bus 2: transmitter enable Bus2_Rx_En : out STD_LOGIC; -- bus 2: receiver enable Bus2_RxD_0 : in STD_LOGIC; -- crate 0 Bus2_TxD_0 : out STD_LOGIC; Bus2_RxD_1 : in STD_LOGIC; -- crate 1 Bus2_TxD_1 : out STD_LOGIC; Bus2_RxD_2 : in STD_LOGIC; -- crate 2 Bus2_TxD_2 : out STD_LOGIC; Bus2_RxD_3 : in STD_LOGIC; -- crate 3 Bus2_TxD_3 : out STD_LOGIC; -- auxiliary access -- Aux_Rx_D : in STD_LOGIC; -- Aux_Tx_D : out STD_LOGIC; -- Aux_Rx_En : out STD_LOGIC; -- Rx- and Tx enable -- Aux_Tx_En : out STD_LOGIC; -- also for auxiliary Trigger-ID -- auxiliary Trigger-ID (i.e. to send the Trigger-ID to the counting hut/house/container) -- TrID_Rx_D : in STD_LOGIC; -- TrID_Tx_D : out STD_LOGIC; -- Crate-Resets ------------------------------------------------------------------------------- -- Crate_Res0 : out STD_LOGIC; -- Crate_Res1 : out STD_LOGIC; -- Crate_Res2 : out STD_LOGIC; -- Crate_Res3 : out STD_LOGIC; -- Busy signals from the FAD boards ------------------------------------------------------------------------------- Busy0 : in STD_LOGIC; Busy1 : in STD_LOGIC; Busy2 : in STD_LOGIC; Busy3 : in STD_LOGIC; -- NIM outputs -- LVDS output at the FPGA followed by LVDS to NIM conversion stage ------------------------------------------------------------------------------- -- calibration -- Cal_NIM1_p : out STD_LOGIC; -- Cal_NIM1+ -- Cal_NIM1_n : out STD_LOGIC; -- Cal_NIM1- -- Cal_NIM2_p : out STD_LOGIC; -- Cal_NIM2+ -- Cal_NIM2_n : out STD_LOGIC; -- Cal_NIM2- -- auxiliarry / spare NIM outputs -- NIM_Out0_p : out STD_LOGIC; -- NIM_Out0+ -- NIM_Out0_n : out STD_LOGIC; -- NIM_Out0- -- NIM_Out1_p : out STD_LOGIC; -- NIM_Out1+ -- NIM_Out1_n : out STD_LOGIC; -- NIM_Out1- -- fast control signal outputs -- LVDS output at the FPGA followed by LVDS to NIM conversion stage ------------------------------------------------------------------------------- -- RES_p : out STD_LOGIC; -- RES+ Reset -- RES_n : out STD_LOGIC; -- RES- TRG_p : out STD_LOGIC; -- TRG+ Trigger TRG_n : out STD_LOGIC; -- TRG- TIM_Run_p : out STD_LOGIC; -- TIM_Run+ Time Marker TIM_Run_n : out STD_LOGIC -- TIM_Run- -- TIM_Sel : out STD_LOGIC; -- Time Marker selector -- CLD_FPGA : in STD_LOGIC; -- DRS-Clock feedback into FPGA -- LVDS calibration outputs ------------------------------------------------------------------------------- -- to connector J13 -- for light pulsar in the mirror dish -- Cal_0_p : out STD_LOGIC; -- Cal_0_n : out STD_LOGIC; -- Cal_1_p : out STD_LOGIC; -- Cal_1_n : out STD_LOGIC; -- Cal_2_p : out STD_LOGIC; -- Cal_2_n : out STD_LOGIC; -- Cal_3_p : out STD_LOGIC; -- Cal_3_n : out STD_LOGIC; -- to connector J12 -- for light pulsar inside shutter -- Cal_4_p : out STD_LOGIC; -- Cal_4_n : out STD_LOGIC; -- Cal_5_p : out STD_LOGIC; -- Cal_5_n : out STD_LOGIC; -- Cal_6_p : out STD_LOGIC; -- Cal_6_n : out STD_LOGIC; -- Cal_7_p : out STD_LOGIC; -- Cal_7_n : out STD_LOGIC -- Testpoints ------------------------------------------------------------------------------- -- TP : inout STD_LOGIC_VECTOR(32 downto 0); -- TP_in : in STD_LOGIC_VECTOR(34 downto 33); -- input only -- Board ID - inputs -- local board-ID "solder programmable" -- all on 'input only' pins ------------------------------------------------------------------------------- -- brd_id : in STD_LOGIC_VECTOR(7 downto 0) -- input only ); end component; --Inputs signal clk_sig : STD_LOGIC := '0'; signal W_INT_sig : STD_LOGIC := '0'; signal W_BRDY_sig : STD_LOGIC_VECTOR(3 downto 0) := (others => '0'); signal Trig_Prim_A_sig : STD_LOGIC_VECTOR(9 downto 0) := (others => '0'); signal Trig_Prim_B_sig : STD_LOGIC_VECTOR(9 downto 0) := (others => '0'); signal Trig_Prim_C_sig : STD_LOGIC_VECTOR(9 downto 0) := (others => '0'); signal Trig_Prim_D_sig : STD_LOGIC_VECTOR(9 downto 0) := (others => '0'); signal ext_Trig_sig : STD_LOGIC_VECTOR(2 downto 1) := (others => '0'); signal Veto_sig : STD_LOGIC := '0'; signal NIM_In_sig : STD_LOGIC_VECTOR(2 downto 0) := (others => '0'); signal NIM_In3_GCLK_sig : STD_LOGIC := '0'; signal LD_Clk_Cond_sig : STD_LOGIC := '1'; signal Bus1_RxD_0_sig : STD_LOGIC := '1'; signal Bus1_RxD_1_sig : STD_LOGIC := '1'; signal Bus1_RxD_2_sig : STD_LOGIC := '1'; signal Bus1_RxD_3_sig : STD_LOGIC := '1'; signal Bus2_RxD_0_sig : STD_LOGIC := '1'; signal Bus2_RxD_1_sig : STD_LOGIC := '1'; signal Bus2_RxD_2_sig : STD_LOGIC := '1'; signal Bus2_RxD_3_sig : STD_LOGIC := '1'; signal Busy0_sig : STD_LOGIC := '0'; signal Busy1_sig : STD_LOGIC := '0'; signal Busy2_sig : STD_LOGIC := '0'; signal Busy3_sig : STD_LOGIC := '0'; --Input/Output Pins signal W_D_sig : STD_LOGIC_VECTOR(15 downto 0) := (others => '0'); signal W_T_sig : STD_LOGIC_VECTOR(3 downto 0) := (others => '0'); signal SIO_sig : STD_LOGIC := '0'; --Outputs signal W_A_sig : STD_LOGIC_VECTOR(9 downto 0); signal W_CS_sig : STD_LOGIC; signal W_RD_sig : STD_LOGIC; signal W_WR_sig : STD_LOGIC; signal W_RES_sig : STD_LOGIC; signal S_CLK_sig : STD_LOGIC; signal TS_CS_sig : STD_LOGIC_VECTOR(3 downto 0); signal LED_red_sig : STD_LOGIC_VECTOR(3 downto 0); signal LED_ye_sig : STD_LOGIC_VECTOR(1 downto 0); signal LED_gn_sig : STD_LOGIC_VECTOR(1 downto 0); signal CLK_Clk_Cond_sig : STD_LOGIC; signal LE_Clk_Cond_sig : STD_LOGIC; signal DATA_Clk_Cond_sig : STD_LOGIC; signal SYNC_Clk_Cond_sig : STD_LOGIC; signal Bus1_Tx_En_sig : STD_LOGIC; signal Bus1_Rx_En_sig : STD_LOGIC; signal Bus1_TxD_0_sig : STD_LOGIC; signal Bus1_TxD_1_sig : STD_LOGIC; signal Bus1_TxD_2_sig : STD_LOGIC; signal Bus1_TxD_3_sig : STD_LOGIC; signal Bus2_Tx_En_sig : STD_LOGIC; signal Bus2_Rx_En_sig : STD_LOGIC; signal Bus2_TxD_0_sig : STD_LOGIC; signal Bus2_TxD_1_sig : STD_LOGIC; signal Bus2_TxD_2_sig : STD_LOGIC; signal Bus2_TxD_3_sig : STD_LOGIC; signal Crate_Res0_sig : STD_LOGIC; signal Crate_Res1_sig : STD_LOGIC; signal Crate_Res2_sig : STD_LOGIC; signal Crate_Res3_sig : STD_LOGIC; signal RES_p_sig : STD_LOGIC; signal RES_n_sig : STD_LOGIC; signal TRG_p_sig : STD_LOGIC; signal TRG_n_sig : STD_LOGIC; signal TIM_Run_p_sig : STD_LOGIC; signal TIM_Run_n_sig : STD_LOGIC; signal TIM_Sel_sig : STD_LOGIC; signal Cal_0_p_sig : STD_LOGIC; signal Cal_0_n_sig : STD_LOGIC; signal Cal_1_p_sig : STD_LOGIC; signal Cal_1_n_sig : STD_LOGIC; signal Cal_2_p_sig : STD_LOGIC; signal Cal_2_n_sig : STD_LOGIC; signal Cal_3_p_sig : STD_LOGIC; signal Cal_3_n_sig : STD_LOGIC; signal Cal_4_p_sig : STD_LOGIC; signal Cal_4_n_sig : STD_LOGIC; signal Cal_5_p_sig : STD_LOGIC; signal Cal_5_n_sig : STD_LOGIC; signal Cal_6_p_sig : STD_LOGIC; signal Cal_6_n_sig : STD_LOGIC; signal Cal_7_p_sig : STD_LOGIC; signal Cal_7_n_sig : STD_LOGIC; -- Clock period definitions constant clk_period : TIME := 25 ns; -- 40 MHZ oscillator U47 --constant baud_rate_period : TIME := 4 us; -- 250 kHz baud rate constant baud_rate_period : TIME := 100 ns; -- 10 MHz baud rate begin -- Instantiate the Unit Under Test (UUT) uut: FTM_top port map( clk => clk_sig, W_D => W_D_sig, W_A => W_A_sig, W_CS => W_CS_sig, W_INT => W_INT_sig, W_RD => W_RD_sig, W_WR => W_WR_sig, W_RES => W_RES_sig, -- W_BRDY => W_BRDY_sig, -- W_T => W_T_sig, -- S_CLK => S_CLK_sig, -- SIO => SIO_sig, -- TS_CS => TS_CS_sig, Trig_Prim_A => Trig_Prim_A_sig, Trig_Prim_B => Trig_Prim_B_sig, Trig_Prim_C => Trig_Prim_C_sig, Trig_Prim_D => Trig_Prim_D_sig, ext_Trig => ext_Trig_sig, Veto => Veto_sig, -- NIM_In => NIM_In_sig, -- NIM_In3_GCLK => NIM_In3_GCLK_sig, LED_red => LED_red_sig, LED_ye => LED_ye_sig, LED_gn => LED_gn_sig, CLK_Clk_Cond => CLK_Clk_Cond_sig, LE_Clk_Cond => LE_Clk_Cond_sig, DATA_Clk_Cond => DATA_Clk_Cond_sig, SYNC_Clk_Cond => SYNC_Clk_Cond_sig, LD_Clk_Cond => LD_Clk_Cond_sig, Bus1_Tx_En => Bus1_Tx_En_sig, Bus1_Rx_En => Bus1_Rx_En_sig, Bus1_RxD_0 => Bus1_RxD_0_sig, Bus1_TxD_0 => Bus1_TxD_0_sig, Bus1_RxD_1 => Bus1_RxD_1_sig, Bus1_TxD_1 => Bus1_TxD_1_sig, Bus1_RxD_2 => Bus1_RxD_2_sig, Bus1_TxD_2 => Bus1_TxD_2_sig, Bus1_RxD_3 => Bus1_RxD_3_sig, Bus1_TxD_3 => Bus1_TxD_3_sig, Bus2_Tx_En => Bus2_Tx_En_sig, Bus2_Rx_En => Bus2_Rx_En_sig, Bus2_RxD_0 => Bus2_RxD_0_sig, Bus2_TxD_0 => Bus2_TxD_0_sig, Bus2_RxD_1 => Bus2_RxD_1_sig, Bus2_TxD_1 => Bus2_TxD_1_sig, Bus2_RxD_2 => Bus2_RxD_2_sig, Bus2_TxD_2 => Bus2_TxD_2_sig, Bus2_RxD_3 => Bus2_RxD_3_sig, Bus2_TxD_3 => Bus2_TxD_3_sig, -- Crate_Res0 => Crate_Res0_sig, -- Crate_Res1 => Crate_Res1_sig, -- Crate_Res2 => Crate_Res2_sig, -- Crate_Res3 => Crate_Res3_sig, Busy0 => Busy0_sig, Busy1 => Busy1_sig, Busy2 => Busy2_sig, Busy3 => Busy3_sig, -- RES_p => RES_p_sig, -- RES_n => RES_n_sig, TRG_p => TRG_p_sig, TRG_n => TRG_n_sig, TIM_Run_p => TIM_Run_p_sig, TIM_Run_n => TIM_Run_n_sig -- TIM_Sel => TIM_Sel_sig, -- Cal_0_p => Cal_0_p_sig, -- Cal_0_n => Cal_0_n_sig, -- Cal_1_p => Cal_1_p_sig, -- Cal_1_n => Cal_1_n_sig, -- Cal_2_p => Cal_2_p_sig, -- Cal_2_n => Cal_2_n_sig, -- Cal_3_p => Cal_3_p_sig, -- Cal_3_n => Cal_3_n_sig, -- Cal_4_p => Cal_4_p_sig, -- Cal_4_n => Cal_4_n_sig, -- Cal_5_p => Cal_5_p_sig, -- Cal_5_n => Cal_5_n_sig, -- Cal_6_p => Cal_6_p_sig, -- Cal_6_n => Cal_6_n_sig, -- Cal_7_p => Cal_7_p_sig, -- Cal_7_n => Cal_7_n_sig ); -- Stimulus process for clock clk_proc: process begin clk_sig <= '0'; wait for clk_period/2; clk_sig <= '1'; wait for clk_period/2; end process clk_proc; -- Stimulus process for busy signals busy_proc: process begin wait for 500us; Busy0_sig <= '1'; wait for 100us; Busy0_sig <= '0'; -- wait for 1ms; -- Busy0_sig <= '1'; -- wait for 500us; -- Busy0_sig <= '0'; wait; end process busy_proc; -- Stimulus process for trigger trigger_proc: process begin --------------------------------------------------------------------------- -- FTUs not yet initialized --------------------------------------------------------------------------- wait for 10us; Trig_Prim_A_sig(0) <= '1'; wait for 100ns; Trig_Prim_A_sig(0) <= '0'; wait for 99us; Trig_Prim_B_sig(0) <= '1'; wait for 100ns; Trig_Prim_B_sig(0) <= '0'; wait for 1us; Trig_Prim_B_sig(0) <= '1'; wait for 100ns; Trig_Prim_B_sig(0) <= '0'; --------------------------------------------------------------------------- -- now FTUs are initialized --------------------------------------------------------------------------- wait for 2200us; Trig_Prim_A_sig(0) <= '1'; Trig_Prim_B_sig(0) <= '1'; wait for 100ns; Trig_Prim_A_sig(0) <= '0'; Trig_Prim_B_sig(0) <= '0'; wait for 4us; Trig_Prim_A_sig(0) <= '1'; wait for 100ns; Trig_Prim_A_sig(0) <= '0'; wait for 22us; Trig_Prim_B_sig(0) <= '1'; wait for 100ns; Trig_Prim_B_sig(0) <= '0'; wait; end process trigger_proc; -- Stimulus process for RS485 of crate 0 rs485_0_proc: process procedure assign_rs485_0 (data: std_logic_vector(7 downto 0)) is begin Bus1_RxD_0_sig <= '0'; --start bit wait for baud_rate_period; Bus1_RxD_0_sig <= data(0); --bit 0 wait for baud_rate_period; Bus1_RxD_0_sig <= data(1); --bit 1 wait for baud_rate_period; Bus1_RxD_0_sig <= data(2); --bit 2 wait for baud_rate_period; Bus1_RxD_0_sig <= data(3); --bit 3 wait for baud_rate_period; Bus1_RxD_0_sig <= data(4); --bit 4 wait for baud_rate_period; Bus1_RxD_0_sig <= data(5); --bit 5 wait for baud_rate_period; Bus1_RxD_0_sig <= data(6); --bit 6 wait for baud_rate_period; Bus1_RxD_0_sig <= data(7); --bit 7 wait for baud_rate_period; Bus1_RxD_0_sig <= '1'; --stop bit wait for baud_rate_period; Bus1_RxD_0_sig <= '1'; --stop bit wait for baud_rate_period; end assign_rs485_0; begin --------------------------------------------------------------------------- -- time of FTU answer --------------------------------------------------------------------------- wait for 1.24ms; --------------------------------------------------------------------------- -- data package of FTU answer (28 byte) --------------------------------------------------------------------------- assign_rs485_0(X"40"); --start delimiter wait for 0us; assign_rs485_0(X"C0"); --FTM address wait for 0ns; assign_rs485_0(X"00"); --FTU address wait for 0ns; assign_rs485_0(X"01"); --FTM firmware ID wait for 0ns; assign_rs485_0(X"02"); --instruction wait for 0us; assign_rs485_0(X"00"); --data byte 01 wait for 0ns; assign_rs485_0(X"F0"); --data byte 02 wait for 0ns; assign_rs485_0(X"00"); --data byte 03 wait for 0ns; assign_rs485_0(X"00"); --data byte 04 wait for 0ns; assign_rs485_0(X"00"); --data byte 05 wait for 0ns; assign_rs485_0(X"00"); --data byte 06 wait for 0ns; assign_rs485_0(X"00"); --data byte 07 wait for 0ns; assign_rs485_0(X"00"); --data byte 08 wait for 0ns; assign_rs485_0(X"00"); --data byte 09 wait for 0ns; assign_rs485_0(X"00"); --data byte 10 wait for 0ns; assign_rs485_0(X"00"); --data byte 11 wait for 0ns; assign_rs485_0(X"00"); --data byte 12 wait for 0ns; assign_rs485_0(X"00"); --data byte 13 wait for 0ns; assign_rs485_0(X"00"); --data byte 14 wait for 0ns; assign_rs485_0(X"00"); --data byte 15 wait for 0ns; assign_rs485_0(X"00"); --data byte 16 wait for 0ns; assign_rs485_0(X"00"); --data byte 17 wait for 0ns; assign_rs485_0(X"00"); --data byte 18 wait for 0ns; assign_rs485_0(X"00"); --data byte 19 wait for 0ns; assign_rs485_0(X"00"); --data byte 20 wait for 0ns; assign_rs485_0(X"00"); --data byte 21 wait for 0ns; assign_rs485_0(X"00"); --CRC error counter (not used) wait for 0ns; assign_rs485_0(X"98"); --check sum for rates --assign_rs485_0(X"A5"); --check sum for ping --------------------------------------------------------------------------- -- don't forget final wait! --------------------------------------------------------------------------- wait; end process rs485_0_proc; end;