# Move Telescope to Wobble Position 1
>
> data taking script for Wobble 1 starting up...
> ----------------------------------------------------
>
> Operator: make sure that telescope is tracking wobble position 1 of source
>
#> ... This script will wait 10sec for you
#.w 10000

FEEDBACK/ENABLE_OUTPUT 1

# Making sure bias is off
BIAS_CONTROL/SET_ZERO_VOLTAGE
.s BIAS_CONTROL 7
FAD_CONTROL/START_DRS_CALIBRATION
> bias voltage is switched off
>
> taking DRS:Pedestal 1000 ...
.s FAD_CONTROL 4
MCP/START -1 1000 drs-pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking DRS:Gain 1000 ...
MCP/START -1 1000 drs-gain
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking DRS:Pedestal 1000 ...
MCP/START -1 1000 drs-pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking crosscheck DRS:Pedestal 1000 ...
FAD_CONTROL/SET_FILE_FORMAT 2
MCP/START -1 1000 drs-pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking DRS:Time 1000 ...
MCP/START -1 1000 drs-time
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking DRS:Time upshifted 1000 ...
MCP/START -1 1000 drs-time-upshifted
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking Pedestal 1000 for secondary baseline...
FAD_CONTROL/RESET_SECONDARY_DRS_BASELINE
MCP/START -1 1000 pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> taking crosscheck Pedestal 1000 ...
FAD_CONTROL/SET_FILE_FORMAT 2
MCP/START -1 1000 pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done
> Operator: Measure Sky Brightness

# switch BIAS ON and ramp to nominal Voltage
> checking feedback state
.s FEEDBACK 12
> ... Current/Temp control active and voltage output enabled
> switching on bias ...
BIAS_CONTROL/SET_GLOBAL_DAC 1
.s BIAS_CONTROL 9 # Voltage ON
> ...set 1 DAC
.s BIAS_CONTROL 5 # Ramping
> ...ramping
.s BIAS_CONTROL 9 # Voltage ON
> ...bias ON
# here one should wait 30..45sec according to TB
> bias is on, and feedback-program is working, but we wait 45sec for the current readings...
.w 45000
> ... done

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking Pedestal with BIAS on 1000 ...
MCP/START -1 1000 pedestal
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking External Light Pulser with BIAS on 1000 ...
MCP/START -1 1000 light-pulser-ext
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

#Data Taking with Full Trigger Area (4x5min)

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking Data:FullTriggerArea 5min Run 1 ...
MCP/START 300 -1 data
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking Data:FullTriggerArea 5min Run 2 ...
MCP/START 300 -1 data
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking Data:FullTriggerArea 5min Run 3 ...
MCP/START 300 -1 data
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

# check if all subsystems are in the correct state
.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
> taking Data:FullTriggerArea 5min Run 4 ...
MCP/START 300 -1 data
.s FAD_CONTROL 8
.s FAD_CONTROL 4
> ... done

> ----------------------------------------------------
> This is the end of data taking of Wobble 1
> ----------------------------------------------------