source: trunk/FACT++/ScriptsForDimCtrl/DataTaking1@ 13706

Last change on this file since 13706 was 13706, checked in by neise, 13 years ago
just changed some logging output, two short '-' lines instead of a long one
File size: 3.4 KB
Line 
1# Move Telescope to Wobble Position 1
2>
3> -----------
4> data taking script for Wobble 1 starting up...
5> -----------
6>
7> Operator: make sure that telescope is tracking wobble position 1 of source
8>
9#> ... This script will wait 10sec for you
10#.w 10000
11
12FEEDBACK/ENABLE_OUTPUT 1
13
14# Making sure bias is off
15BIAS_CONTROL/SET_ZERO_VOLTAGE
16.s BIAS_CONTROL 7
17FAD_CONTROL/START_DRS_CALIBRATION
18> bias voltage is switched off
19>
20> taking DRS:Pedestal 1000 ...
21.s FAD_CONTROL 4
22MCP/START -1 1000 drs-pedestal
23.s FAD_CONTROL 8
24.s FAD_CONTROL 4
25> ... done
26
27> taking DRS:Gain 1000 ...
28MCP/START -1 1000 drs-gain
29.s FAD_CONTROL 8
30.s FAD_CONTROL 4
31> ... done
32
33> taking DRS:Pedestal 1000 ...
34MCP/START -1 1000 drs-pedestal
35.s FAD_CONTROL 8
36.s FAD_CONTROL 4
37> ... done
38
39> taking crosscheck DRS:Pedestal 1000 ...
40FAD_CONTROL/SET_FILE_FORMAT 2
41MCP/START -1 1000 drs-pedestal
42.s FAD_CONTROL 8
43.s FAD_CONTROL 4
44> ... done
45
46> taking DRS:Time 1000 ...
47MCP/START -1 1000 drs-time
48.s FAD_CONTROL 8
49.s FAD_CONTROL 4
50> ... done
51
52> taking DRS:Time upshifted 1000 ...
53MCP/START -1 1000 drs-time-upshifted
54.s FAD_CONTROL 8
55.s FAD_CONTROL 4
56> ... done
57
58> taking Pedestal 1000 for secondary baseline...
59FAD_CONTROL/RESET_SECONDARY_DRS_BASELINE
60MCP/START -1 1000 pedestal
61.s FAD_CONTROL 8
62.s FAD_CONTROL 4
63> ... done
64
65> taking crosscheck Pedestal 1000 ...
66FAD_CONTROL/SET_FILE_FORMAT 2
67MCP/START -1 1000 pedestal
68.s FAD_CONTROL 8
69.s FAD_CONTROL 4
70> ... done
71> Operator: Measure Sky Brightness
72
73# switch BIAS ON and ramp to nominal Voltage
74> checking feedback state
75.s FEEDBACK 12
76> ... Current/Temp control active and voltage output enabled
77> switching on bias ...
78BIAS_CONTROL/SET_GLOBAL_DAC 1
79.s BIAS_CONTROL 9 # Voltage ON
80> ...set 1 DAC
81.s BIAS_CONTROL 5 # Ramping
82> ...ramping
83.s BIAS_CONTROL 9 # Voltage ON
84> ...bias ON
85# here one should wait 30..45sec according to TB
86> bias is on, and feedback-program is working, but we wait 45sec for the current readings...
87.w 45000
88> ... done
89
90# check if all subsystems are in the correct state
91.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
92> taking Pedestal with BIAS on 1000 ...
93MCP/START -1 1000 pedestal
94.s FAD_CONTROL 8
95.s FAD_CONTROL 4
96> ... done
97
98# check if all subsystems are in the correct state
99.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
100> taking External Light Pulser with BIAS on 1000 ...
101MCP/START -1 1000 light-pulser-ext
102.s FAD_CONTROL 8
103.s FAD_CONTROL 4
104> ... done
105
106#Data Taking with Full Trigger Area (4x5min)
107
108# check if all subsystems are in the correct state
109.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
110> taking Data:FullTriggerArea 5min Run 1 ...
111MCP/START 300 -1 data
112.s FAD_CONTROL 8
113.s FAD_CONTROL 4
114> ... done
115
116# check if all subsystems are in the correct state
117.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
118> taking Data:FullTriggerArea 5min Run 2 ...
119MCP/START 300 -1 data
120.s FAD_CONTROL 8
121.s FAD_CONTROL 4
122> ... done
123
124# check if all subsystems are in the correct state
125.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
126> taking Data:FullTriggerArea 5min Run 3 ...
127MCP/START 300 -1 data
128.s FAD_CONTROL 8
129.s FAD_CONTROL 4
130> ... done
131
132# check if all subsystems are in the correct state
133.x ScriptsForDimCtrl/ServiceScripts/IsReadyForDataTaking
134> taking Data:FullTriggerArea 5min Run 4 ...
135MCP/START 300 -1 data
136.s FAD_CONTROL 8
137.s FAD_CONTROL 4
138> ... done
139
140> ----------------------------------------------------
141> This is the end of data taking of Wobble 1
142> ----------------------------------------------------
Note: See TracBrowser for help on using the repository browser.