# ==========================================================================
#############################################################################
# ==========================================================================
#                              General
# ==========================================================================
#############################################################################
# ==========================================================================

# -------------------------------------------------------------------------
# Use this if you want to setup the logging stream for the jobs
# (overwrites command line options)
# -------------------------------------------------------------------------
#MLog.VerbosityLevel: 2
#MLog.DebugLevel:     1
#MLog.NoColors:       yes

# ==========================================================================
#############################################################################
# ==========================================================================
#                                   Star
# ==========================================================================
#############################################################################
# ==========================================================================

# -------------------------------------------------------------------------
# Use this if you want to write the MJStar output somewhere
# If you don't want it, it is written to the calibration output anyhow.
# -------------------------------------------------------------------------
#MJStar.PathOut: .
#MJStar.PathIn: .

# -------------------------------------------------------------------------
# Configure MJStar
# -------------------------------------------------------------------------
#MJStar.MaxEvents: 10000
#MJStar.Overwrite: yes,no

# -------------------------------------------------------------------------
# Use this if you want to change the parameters of the software trigger
# -------------------------------------------------------------------------
#FilterSwTrigger.Threshold:    5
#FilterSwTrigger.NumNeighbors: 4
#FilterSwTrigger.TimeWindow:   0.5

# -------------------------------------------------------------------------
# Setup the image cleaning here
# -------------------------------------------------------------------------
MImgCleanStd.CleanLevel1: 8.5
MImgCleanStd.CleanLevel2: 4.0
MImgCleanStd.CleanMethod: Absolute
#MImgCleanStd.CleanRings: 1
#MImgCleanStd.KeepSinglePixels: No

# -------------------------------------------------------------------------
# Setup the cut applied to the Sparkless tab
# -------------------------------------------------------------------------

# This is the simple default
#SparkCut.Condition: log10(MNewImagePar.fConc1) < (-0.371)*log10(MHillas.fSize) + 0.596

# This is the more complicated cut from ganymed.rc
#SparkCut.Condition: ({0} || {1}) && {2}
#SparkCut.0: MImagePar.fNumSatPixelsHG < 1
#SparkCut.1: MHillas.GetArea*(MGeomCam.fConvMm2Deg^2) > (0.003*MImagePar.fNumSatPixelsHG) + 0.0325
#SparkCut.2: log10(MNewImagePar.fConc1) < (-0.371)*log10(MHillas.fSize) + 0.596

# -------------------------------------------------------------------------
# setup the image parameter calculation here
# -------------------------------------------------------------------------
#MHillasCalc.IdxIsland: 0

# -------------------------------------------------------------------------
# Setup or switch off the muon analysis here
# -------------------------------------------------------------------------
#MJStar.MuonAnalysis: On

#MMuonSetup.Margin:            0.2
#MMuonSetup.ThresholdArcPhi:   30
#MMuonSetup.ThresholdArcWidth: 2

#BinningRadius.Raw:            20  0.5  1.5
#BinningArcWidth.Raw:          60  0.0  0.3
#BinningRingBroadening.Raw:    20  0.5  1.5
#BinningSizeVsArcRadius.Raw:   20  0.5  1.5
#BinningsArcPhi.Raw:           20 -180  180
#BinningsMuonWidth.Raw:        28  0.3  1.7

#MuonPreCut.Condition:   MHillas.fSize>150
#MuonSearcCut.Condition: (MMuonSearchPar.fRadius>180) && (MMuonSearchPar.fRadius<400) && (MMuonSearchPar.fDeviation<45)
#MuonFinalCut.Condition: (MMuonCalibPar.fArcPhi>190)  && (MMuonSearchPar.fDeviation<35) && (MMuonCalibPar.fArcWidth<0.20) && (MMuonCalibPar.fArcWidth>0.04)