source: firmware/FSC/src/FSC.c@ 10106

Last change on this file since 10106 was 10106, checked in by neise, 14 years ago
Niculin changed something in the presentation of the data
File size: 8.9 KB
Line 
1//-----------------------------------------------------------------------------
2#include "typedefs.h"
3#include "application.h"
4#include "spare_outs.h"
5#include "spi_master.h"
6#include "ad7719_adc.h"
7#include "usart.h"
8#include "macros.h"
9#include "interpol.h"
10#include "w5100_spi_interface.h"
11#include <avr/interrupt.h>
12#include <avr/wdt.h>
13#include <stdlib.h>
14
15#include "tests.h"
16//-----------------------------------------------------------------------------
17
18int main(void)
19{
20// U08 IDN_STR[] = "16ch Pt1000 logger; firmware version of 07.11.10. DN"; // Identity string
21
22 spare_outs_init(); //set spare out pin I/O modes
23 app_init(); // Setup software modules
24 usart_init(); // Initialize serial interface
25 spi_init(); // Initialize SPI interface as master
26 adc_init(); // Initialize AD7719 ADC as SPI slave
27 // usart_write_crlf();
28 // usart_writeln_flash_str(IDN_STR); // Write string to USART interface
29 // usart_write_crlf();
30
31 // Enable interrupts
32 sei();
33
34
35 // temperature muxer pins init:
36 // SA - pins
37 DDRA |= 0x3F; // set all SA-pins as outputs
38
39
40 // voltage, current, humidity - muxer pins:
41 // SB - pins
42 DDRC |= 0x7F; // set all SB - pins as outputs
43
44 // SB - muxer test
45// DDRA |= 1<<PA6 ; // set D0-0 lina as output. for tests only !!!
46// PORTA |= 1<<PA6; // set D0-0 line high. for tests only !!!
47DDRA &= ~(1<<PA6);
48
49//ADC einschalten
50 ADMUX = 0x26; //0010.0110 // interne Referenzspannung nutzen
51 ADCSRA = (1<<ADPS1) | (1<<ADPS0); // Frequenzvorteiler
52 ADCSRA |= (1<<ADEN); // ADC aktivieren
53 ADCSRA |= (1<<ADSC);
54
55
56
57// Main loop
58//float temperature;
59float resistance;
60BOOL heartbeat_enable = TRUE;
61
62U08 SA_mux_val = 0x16;
63U08 SB_mux_val = 0x00;
64
65//U08 counter = 0;
66U08 Res_or_Volt = 0x00;
67
68
69while (TRUE)
70 {
71 // this heartbeat shows how long one single run of this while loop takes
72 // measure with a scope.
73 if (heartbeat_enable) PORTB ^= (1<<PB3); // toggle Out2_spare --> heartbeat
74 adc_init();
75
76 ++Res_or_Volt;
77 if (Res_or_Volt <= 64){
78
79
80 // if USART data arrives. i.e. data via USB
81 // the usart_rx_ready flag is set TRUE
82 // now process the incoming data which is stored in
83 // U08 usart_rx_buffer[USART_RX_BUFFER_SIZE]
84 // and tell the USART interface, it may receive new data
85 // by setting the usart_rx_ready flag FALSE again
86 ++SA_mux_val;
87 if (Res_or_Volt == 1) SB_mux_val = 16;
88 else if (SA_mux_val == 64) SA_mux_val = 32;
89 else if (SA_mux_val == 16) SA_mux_val = 48;
90 else if (SA_mux_val == 32) SA_mux_val = 0;
91 PORTA = (SA_mux_val & 0x3F);
92
93// usart_write_str((pU08)"SA:");
94 usart_write_U08(SA_mux_val,2);
95 usart_write_str((pU08)" Sensor:");
96 usart_write_U08((SA_mux_val % 8)+1,2);
97 usart_write_str((pU08)" an Temperatur_");
98 switch (SA_mux_val / 8)
99 {
100 case 0: usart_write_str((pU08)"C");
101 break;
102 case 1: usart_write_str((pU08)"D");
103 break;
104 case 2: usart_write_str((pU08)"A");
105 break;
106 case 3: usart_write_str((pU08)"B");
107 break;
108 case 4: usart_write_str((pU08)"G");
109 break;
110 case 5: usart_write_str((pU08)"H");
111 break;
112 case 6: usart_write_str((pU08)"E");
113 break;
114 case 7: usart_write_str((pU08)"F");
115 break;
116 default: usart_write_str((pU08)"alarm!");
117 break;
118 }
119// usart_write_str((pU08)"\n");
120 usart_write_str((pU08)" ");
121
122
123 startconv();
124
125
126 while (!ADC_IS_READY())
127 {
128 // just wait until ADC is redy -- really bad code here!
129 }
130
131 resistance = getresistance();
132 //Start a new A/D Conversion
133 //temp = readandsendtemp();
134 //adcword = getadc();
135
136 //temperature = gettemp();
137 usart_write_str((pU08)"R:");
138 usart_write_float(resistance,3,4);
139 usart_write_str((pU08)"kOhm ");
140
141 //_delay_ms(200);
142
143 startconv();
144
145 while (!ADC_IS_READY())
146 {
147 // just wait until ADC is redy -- really bad code here!
148 }
149 //Start a new A/D Conversion
150 //temp = readandsendtemp();
151 //adcword = getadc();
152 resistance = getresistance();
153 //temperature = gettemp();
154 usart_write_str((pU08)"R:");
155 usart_write_float(resistance,3,4);
156 usart_write_str((pU08)"kOhm ");
157
158//usart_write_str((pU08)"\n");
159switch (SA_mux_val)
160 {
161 case 7: usart_write_str((pU08)"\n\n");
162 break;
163 case 15: usart_write_str((pU08)"\n\n");
164 break;
165 case 23: usart_write_str((pU08)"\n\n");
166 break;
167 case 31: usart_write_str((pU08)"\n\n");
168 break;
169 case 39: usart_write_str((pU08)"\n\n");
170 break;
171 case 47: usart_write_str((pU08)"\n\n");
172 break;
173 case 55: usart_write_str((pU08)"\n\n");
174 break;
175 case 63: usart_write_str((pU08)"\n\n");
176 break;
177 default: usart_write_str((pU08)"\n");
178 break;
179 }
180SB_mux_val = 0;
181}
182else if (Res_or_Volt == 148) Res_or_Volt = 0;
183else {
184
185
186 ++SB_mux_val;
187 if (SB_mux_val == 84) SB_mux_val = 0;
188 else if (SB_mux_val == 74) SB_mux_val = 82;
189 else if (SB_mux_val == 82) SB_mux_val = 72;
190 else if (SB_mux_val == 72) SB_mux_val = 74;
191 else if (SB_mux_val == 48) SB_mux_val = 64;
192 else if (SB_mux_val == 64) SB_mux_val = 32;
193 else if (SB_mux_val == 32) SB_mux_val = 48;
194 PORTC = (SB_mux_val & 0x7F);
195
196
197
198
199usart_write_str((pU08)"8bit-ADC: ");
200
201if (SB_mux_val < 64)
202{
203 switch (SB_mux_val / 16)
204 {
205 case 0: usart_write_str((pU08)"voltage_A: ");
206 break;
207 case 1: usart_write_str((pU08)"voltage_B: ");
208 break;
209 case 2: usart_write_str((pU08)"voltage_D: ");
210 break;
211 case 3: usart_write_str((pU08)"voltage_C: ");
212 break;
213 }
214
215 if (SB_mux_val % 2 == 0) {
216 usart_write_str((pU08)"U");
217 usart_write_U08( (SB_mux_val%16)/2 , 1 );
218 } else {
219 usart_write_str((pU08)"I");
220 usart_write_U08( ((SB_mux_val%16)-1)/2 , 1 );
221 }
222
223
224} else {
225
226
227 if (SB_mux_val < 72) {
228 usart_write_str((pU08)"voltage_E: ");
229 if (SB_mux_val % 2 == 0) {
230 usart_write_str((pU08)"U");
231 usart_write_U08( (SB_mux_val%8)/2 , 1 );
232 } else {
233 usart_write_str((pU08)"I");
234 usart_write_U08( ((SB_mux_val%8)-1)/2 , 1 );
235 }
236
237 }
238else if (SB_mux_val == 72) usart_write_str((pU08)"humidity_A: H0");
239else if (SB_mux_val == 73) usart_write_str((pU08)"humidity_A: H1");
240
241else if (SB_mux_val < 82) {
242 usart_write_str((pU08)"voltage_F: ");
243 if (SB_mux_val % 2 == 0) {
244 usart_write_str((pU08)"U");
245 usart_write_U08( ((SB_mux_val-2)%8)/2 , 1 );
246 } else {
247 usart_write_str((pU08)"I");
248 usart_write_U08( (((SB_mux_val-2)%8)-1)/2 , 1 );
249 }
250
251 }
252else if (SB_mux_val == 82) usart_write_str((pU08)"humidity_B: H0");
253else if (SB_mux_val == 83) usart_write_str((pU08)"humidity_B: H1");
254}
255
256for (U08 counter = 0; counter < 1; ++counter) {
257 ADCSRA |= (1<<ADSC);
258 while (ADCSRA & (1<<ADSC) ); // wait until internal ADC is ready
259 float voltage;
260 voltage = ( (float)ADCH ) / 256 * 4.096;
261 usart_write_str((pU08)" ");
262 usart_write_float(voltage,3,4);
263
264
265}
266//usart_write_str((pU08)"\n");
267
268switch (SB_mux_val)
269 {
270 case 15: usart_write_str((pU08)"\n\n");
271 break;
272 case 31: usart_write_str((pU08)"\n\n");
273 break;
274 case 47: usart_write_str((pU08)"\n\n");
275 break;
276 case 63: usart_write_str((pU08)"\n\n");
277 break;
278 case 71: usart_write_str((pU08)"\n\n");
279 break;
280 case 73: usart_write_str((pU08)"\n\n");
281 break;
282 case 81: usart_write_str((pU08)"\n\n");
283 break;
284 case 83: usart_write_str((pU08)"\n\n");
285 break;
286 default: usart_write_str((pU08)"\n");
287 break;
288 }
289
290SA_mux_val = 15;
291}
292 /*
293 if ( usart_rx_ready == TRUE )
294 {
295 //understand what it means and react
296
297 switch (usart_rx_buffer[0])
298 {
299
300 case 'h':
301 {
302 // toggle the heartbeat mode on or off.
303 heartbeat_enable = !heartbeat_enable;
304 break;
305 }
306 case 'a':
307 {
308 // conduct adc - AD7719 SPI interface test
309
310 break;
311 }
312 case 'e':
313 {
314 // conduct ethernet module SPI interface test
315 strtol((char*) usart_rx_buffer+1, NULL, 0);
316 break;
317 }
318
319 default:
320 {
321 usart_write_str((pU08)"? you wrote: ");
322 usart_write_str((pU08)usart_rx_buffer);
323 usart_write_str((pU08)"\n");
324 break;
325 }
326 }
327
328 heartbeat_enable = !heartbeat_enable;
329 usart_rx_ready = FALSE;
330 }
331*/
332// das ist ein paar schritte zu früh.
333// erstmal müssen die interfaces getestet werden.
334/*
335
336 for (U08 i = 0; i<16; i++)
337 {
338
339 if((~PIND) & 0x08) // PD4 is #ADC_RDY input. Inverted logic! if PD4=0 this evaluates to true
340 {
341 PORTA = (PORTA & 0xF0) | ((i) & 0x0F); // switch muxer
342 startconv(); //Start a new A/D Conversion
343 //temp = readandsendtemp();
344 //adcword = getadc();
345 //resistance = getresistance();
346 temperature = gettemp();
347 usart_write_float(temperature,2,4);
348 usart_write_str((pU08)"\t");
349
350 } // end of if adc ready
351 else
352 {
353 i--;
354 }
355 } // end of for loop over 16 channels
356 usart_write_crlf();
357
358*/
359
360 } // end of infinite while loop
361} // end of main()
362
363
364
Note: See TracBrowser for help on using the repository browser.