Spectrum Analysis

The differential flux \phi(E) per area, time and energy interval is defined as \phi(E) = \frac{dN}{dA\cdot dt\cdot dE}

Often \phi(E) is also referred to as \frac{dN}{dE} as observation time and effective collection area is a constant. The effective area is then defined as A_\textrm{eff}(E)=\epsilon(E)\cdot A_0. Note that at large distances R_0 the efficiency \epsilon(R_0) vanishes, so that the effective area is an (energy dependent) constant while A_0=\pi R_0^2 and the efficiency \epsilon(E) are mutually dependent.

For an observation with an effective observation time \Delta T=\sum\delta t_i, this yields in a given Energy interval \Delta E: \phi(\Delta E) = \frac{1}{A_0\cdot \Delta T}\frac{N(\Delta E)}{\epsilon(\Delta E)\cdot \Delta E}

For simplicity, in the following, \Delta E will be replaced by just E but always refers to to a given energy interval. If data is binned in a histogram, the relation between the x-value for the bin E_\textrm{x} and the corresponding interval \Delta E_\textrm{x} is not well defined. Resonable definitions are the bin center (usually in logarithmic bins) or the average energy.

The total area A_0 and the corresponding efficiency \epsilon(E) are of course only available for simulated data. For simulated data, A_0 is the production area and \epsilon(E) the corresponding energy dependent efficiency of the analysis chain. For a given energy bin, the efficiency is then defined as

\epsilon(E) = \frac{N_\textrm{exc}(E)}{N_0(E)}

where N_0 is the number of simulated events in this energy bin and N=N_{exc} the number of *excess* events that are produced by the analysis chain.

Note that the exact calculation of the efficiency \epsilon(\Delta E) depends on prior knowledge of the correct source spectrum N_0(E). Therefore, it is strictly speaking only correct if the simulated spectrum and the real spectrum are identical. As the real spectrum is unknown, special care has to be taken of the systematic introduced by the assumption of N_0(E).

Excess

The number of excess events, for data and simulations, is defined as

N_\textrm{exc} = N_\textrm{sig} - \hat N_\textrm{bg}

where N_\textrm{sig} is the number of events identified as potential gammas from the source direction ('on-source') and N_\textrm{bg} the number of gamma-like events measured 'off-source'. Note that for Simulations, \hat N_\textrm{bg} is not necessarily zero for wobble-mode observations as an event can survive the analysis for on- and off-events, if this is not prevented by the analysis (cuts).

The average number of background events \hat N_\textrm{bg} is the total number of background events N_\textrm{bg} from all off-regions times the corresponding weight \frac{1}{5} (often referred to as \alpha). For five off-regions, this yields

\hat N_\textrm{bg} = \frac{N_\textrm{bg}}{5}

Assuming Gaussian errors, the statistical error is thus

\sigma^2(N_\textrm{exc}) = \left(\frac{dN_\textrm{exc}}{dN_\textrm{sig}}\right)^2\sigma^2(N_\textrm{sig}) + \left(\frac{dN_\textrm{exc}}{d\hat N_\textrm{bg}}\right)^2\sigma^2(\hat N_\textrm{bg})= \sigma^2(N_\textrm{sig}) + \frac{1}{5^2}\sigma^2(N_\textrm{bg})

For data this immediately resolves to

\sigma^2(N_\textrm{exc}) = N_\textrm{sig} + \frac{1}{5^2}N_\textrm{bg}

with the Poisson (counting) error \sigma^2(N_\textrm{sig,bg}) = N_\textrm{sig,bg}.

Code

In the following N refers to a number of simulated events and M to a number of measured (excess) events.

n(\delta E, \delta\theta) is the number of produced events in the energy interval E\in\delta E=[e_\textrm{min};e_\textrm{max}] and the zenith angle interval \theta\in\delta\theta=[\theta_\textrm{min};\theta_\textrm{max}]. The weighted number of events n'(\delta E, \delta\theta) in that interval is then

n'(\delta E, \delta\theta) = \sum_{i=0...n}^{E\in\delta E}\sum_{j=0...n}^{\theta\in\delta\theta} \omega(E_i, \theta_j)

Since \omega(E, \theta) = \rho(E)\cdot \tau(\theta) with \rho(E) the spectral weight to adapt the spectral shape of the simulated spectrum to the real (measured) spectrum of the source and \tau(\theta) the weight to adapt to oberservation time versus zenith angle.

n'(\delta E, \delta\theta) = \sum_{i=0...n}^{E\in\delta E}\sum_{j=0...n}^{\theta\in\delta\theta} \rho(E_i)\cdot\tau(\theta_j) = \sum_{i=0...n}^{E\in\delta E}\rho(E_i)\cdot\sum_{j=0...n}^{\theta\in\delta\theta} \tau(\theta_j)

The weighted number of produced events N'(\Delta E, \Delta\Theta) in the total energy interval E\in\Delta E=[E_\textrm{min};E_\textrm{max}] and the total zenith angle interval \theta\in\Delta\Theta=[\Theta_\textrm{min};\Theta_\textrm{max}] is then

N'(\Delta E, \Delta\Theta) = \sum_{i=0...N}^{E\in\Delta E}\sum_{j=0...N}^{\theta\in\Delta\Theta} \rho(E_i)\cdot\tau(\theta_j) = \sum_{i=0...N}^{E\in\Delta E}\rho(E_i)\cdot\sum_{j=0...N}^{\theta\in\Delta\Theta} \tau(\theta_j)

with N(\Delta E, \Delta\Theta) being the total number of produced events.

For a sum of weights, e.g. N' = \sum_N \rho_i\tau_i the corresponding error is \sigma^2(N')^2 = \sum_N\left[\rho_i\cdot\sigma(\tau_i)+\tau_i\cdot\sigma(\rho_i)\right]^2

As the energy is well defined, \sigma(\rho_i)=0 and thus

\sigma^2(N')^2 = \sum_N\rho_i^2\cdot\sigma^2(\tau_i)

The weights are defined as follow:

\rho(E) = \rho_0\frac{\phi_\textrm{src}(E)}{\phi_0(E)}

where \phi_0(E) is the simulated spectrum and \phi_\textrm{src} the (unknown) real source spectrum. \rho_0 is a normalization constant. The zenith angle weights \tau(\delta\theta) in the interval \delta\theta are defined as

\tau(\delta\theta) = \tau_0\frac{\Delta T(\delta\theta)}{N(\delta\theta)}

where N(\delta\theta) is the number of produced events in the interval \delta\theta and \Delta T(\delta\theta) is the total observation time in the same zenith angle interval. \tau_0 is the normalization constant. The error on the weight \tau=\tau(\delta\theta) in each individual \theta-bin with \Delta T=\Delta T(\delta\theta) and N=N(\delta\theta)is then

\sigma^2(\tau) = \left[\frac{d\tau}{d\Delta T}\sigma(\Delta T)\right]^2+\left[\frac{d\tau}{dN}\sigma(N)\right]^2= \tau^2\cdot\left[\left(\frac{\sigma(\Delta T)}{\Delta T}\right)^2+\left(\frac{\sigma(N)}{N}\right)^2\right]

While \sigma(\Delta T)/\Delta T \approx 1\textrm{s}/5\textrm{min} is given by the data acquisition and 1s per 5min run, \sigma(N)/N=1/\sqrt{N} is just the statistical error of the number of events.

As the efficiency \epsilon(\delta E) for an energy interval \delta E is calculated as

\epsilon(\delta E) = \epsilon(\delta E, \Delta\Theta) = \frac{N'_\textrm{exc}(\delta E, \Delta\Theta)}{N'_\textrm{src}(\delta E,\Delta\Theta)}

and N'_\textrm{exc}(\delta E,\Delta\Theta) and N'_\textrm{src}(\delta E,\Delta\Theta) are both expressed as the sum given above, the constants \rho_0 and \tau_0 cancel.

The differential flux in an energy interval \delta E is then given as

\phi(\delta E) = \phi(\delta E,\Delta\Theta) = \frac{1}{A_0\cdot \Delta T}\frac{M_\textrm{exc}(\delta E)}{\epsilon(\delta E)\cdot \delta E} = \frac{M_\textrm{exc}(\delta E)}{N'_\textrm{exc}(\delta E)}\cdot \frac{N'_\textrm{src}(\delta E)}{A_0\cdot\Delta T\cdot \delta E}

Where A_0 is total area of production and \Delta T the total observation time. The number of measured excess events is in that energy interval is M_\textrm{exc}(\delta E)=M_\textrm{exc}(\delta E, \Delta\Theta).

Using Gaussian error propagation, the error in a given energy interval \delta is then given by

\sigma^2(\phi) = \left(\frac{1}{A_0\cdot \Delta T\cdot\delta E}\right)^2\cdot\left[\left(\frac{d\phi'}{dM_\textrm{exc}}\right)^2\sigma^2(M_\textrm{exc}) + \left(\frac{d\phi'}{dN'_\textrm{exc}}\right)^2\sigma^2(N'_\textrm{exc}) + \left(\frac{d\phi'}{dN'_\textrm{src}}\right)^2\sigma^2(N'_\textrm{src})\right]

with \phi':=A_0\cdot\Delta T\cdot\delta E\cdot\phi.

\rightarrow\quad\sigma^2(\phi) = \phi^2 \cdot\left[\left(\frac{\sigma(M_\textrm{exc})}{M_\textrm{exc} }\right)^2 + \left(\frac{\sigma(N'_\textrm{exc})}{N'_\textrm{exc}}\right)^2 + \left(\frac{\sigma(N'_\textrm{src})}{N'_\textrm{src}}\right)^2\right]

Define Binnings

Get Data File List

A list with file IDs containing the events to be analyed is required a.t.m. The following query retrieves such a list and fills a temporary table (DataFiles) with the IDs.

CREATE TEMPORARY TABLE DataFiles
(
   FileId INT UNSIGNED NOT NULL,
   PRIMARY KEY (FileId) USING HASH
) ENGINE=Memory
AS
(
   SELECT
      FileId
   FROM
      factdata.RunInfo
   WHERE
      %0:where
   ORDER BY
      FileId
)

%0:where is a placeholder, for example for

fZenithDistanceMean<30 AND fThresholdMinSet<350 AND 
fSourceKEY=5 AND 
fRunTypeKEY=1 AND 
fNight>20161201 AND fNight<20170201 AND
fR750Cor>0.9e0*fR750Ref

Get Observation Time

The following query bins the effective observation time of the runs listed above in zenith angle bins and stores the result in a temporary table (ObservationTime). Note that the result contains only those bins which have entries.

CREATE TEMPORARY TABLE ObservationTime
(
   `.theta` SMALLINT UNSIGNED NOT NULL,
   OnTime FLOAT NOT NULL,
   PRIMARY KEY (`.theta`) USING HASH
) ENGINE=Memory
AS
(
   SELECT
      INTERVAL(fZenithDistanceMean, %0:bins) AS `.theta`,
      SUM(TIME_TO_SEC(TIMEDIFF(fRunStop,fRunStart))*fEffectiveOn) AS OnTime
   FROM
      DataFiles
   LEFT JOIN
      factdata.RunInfo USING (FileId)
   GROUP BY
      `.theta`
   ORDER BY
      `.theta`
)

%0:bins is a placeholder for the bin boundaries, e.g. 5, 10, 15, 20, 25, 30 (five bins between 5° and 30° plus underflow and overflow).

Get Monte Carlo File List

The next query obtains all Monte Carlo runs which have their ThetaMin or ThetaMax within one of the bins obtained in the previous query (so all MC runs that correspond to bins in which data is available). Strictly speaking, this step is not necessary, but it accelerats further processing. In addition (here as an example) only runs with even FileIDs are obtained as test-runs (assuming that odd runs were used for training). The resulting FileIDs are stored in a temporary table (MonteCarloFiles).

CREATE TEMPORARY TABLE MonteCarloFiles
(
   FileId INT UNSIGNED NOT NULL,
   PRIMARY KEY (FileId) USING HASH
) ENGINE=Memory
AS
(
   SELECT
      FileId
   FROM
      ObservationTime
   LEFT JOIN
      BinningTheta ON `.theta`=bin
   LEFT JOIN
      factmc.RunInfoMC
   ON
      (ThetaMin>=lo AND ThetaMin<hi) OR (ThetaMax>lo AND ThetaMax<=hi)
   WHERE
      PartId=1 AND
      FileId%%2=0
   ORDER BY
      FileId
)

Get Zenith Angle Histogram

CREATE TEMPORARY TABLE ThetaHist
(
   `.theta`    SMALLINT UNSIGNED NOT NULL,
   lo          DOUBLE            NOT NULL COMMENT 'Lower edge of zenith distance bin in degree',
   hi          DOUBLE            NOT NULL COMMENT 'Upper edge of zenith distance bin in degree',
   CountN      INT UNSIGNED      NOT NULL,
   OnTime      FLOAT             NOT NULL,
   ZdWeight    DOUBLE            NOT NULL COMMENT 'tau(delta theta)',
   ErrZdWeight DOUBLE            NOT NULL COMMENT 'sigma(tau)',
   PRIMARY KEY (`.theta`) USING HASH
) ENGINE=Memory
AS
(
   WITH EventCount AS
   (
      SELECT
         INTERVAL(DEGREES(Theta), %0:bins) AS `.theta`,
         COUNT(*) AS CountN
      FROM
         MonteCarloFiles
      LEFT JOIN
         factmc.OriginalMC USING(FileId)
      GROUP BY
         `.theta`
   )
   SELECT
      `.theta`, lo, hi,
      CountN,
      OnTime,
      OnTime/CountN AS ZdWeight,
      (OnTime/CountN)*SQRT(POW(1/300, 2) + 1/CountN) AS ErrZdWeight
   FROM
      ObservationTime
   LEFT JOIN
      EventCount USING(`.theta`)
   LEFT JOIN
      BinningTheta ON `.theta`=bin
   ORDER BY
      `.theta`
)

Analyze Data

Analyze Monte Carlo Data

Summarize Corsika Production

CREATE TEMPORARY TABLE SimulatedSpectrum
(
   `.energy` SMALLINT UNSIGNED NOT NULL COMMENT 'Bin Index [MC Energy]',
   CountN    DOUBLE            NOT NULL,
   CountW    DOUBLE            NOT NULL,
   CountW2   DOUBLE            NOT NULL,
   PRIMARY KEY (`.energy`) USING HASH
) ENGINE=Memory
AS
(
   SELECT
      INTERVAL(LOG10(Energy), %0:energyest) AS `.energy`,
      COUNT(*) AS CountN,
      SUM(    (%2:spectrum)/pow(Energy, SpectralIndex)   ) AS CountW,
      SUM(POW((%2:spectrum)/pow(Energy, SpectralIndex),2)) AS CountW2
   FROM
      MonteCarloFiles
   LEFT JOIN
      factmc.RunInfoMC USING (FileId)
   LEFT JOIN
      factmc.OriginalMC USING (FileId)
   GROUP BY
      `.energy`
   ORDER BY
      `.energy`
)

Result (Spectrum)

Result (Threshold)

Result (Migration)