16:42 Changeset [10145] by neise
16:29 Changeset [10144] by neise
16:13 Changeset [10143] by ogrimm
Non-blocking configuration request did not recognize default value
12:44 Changeset [10142] by neise
12:09 Changeset [10141] by neise
12:08 Changeset [10140] by neise
11:58 Changeset [10139] by neise
doc folder created
11:54 Changeset [10138] by neise
08:17 Changeset [10137] by neise
added some comments and did some formating
08:09 Changeset [10136] by neise
08:08 Changeset [10135] by neise
08:06 Changeset [10134] by neise
08:06 Changeset [10133] by neise
08:02 Changeset [10132] by neise
07:46 Changeset [10131] by neise
added some files - only important for HDL designer


15:36 Changeset [10130] by tbretz
Fixed a bug in MreadReports which caused the reading to get corrupted as soon as the first event tree was fully read.
14:35 Changeset [10129] by neise
checking before change of Event Header structure. added REFCLK counter and ADC CLK PS output. In case of missing REFCLK, DENEABLE should be pulled low. (untested)
12:32 Changeset [10128] by ogrimm
Warning for data taking if amplitude calibration not done


10:51 Changeset [10127] by weitzel
ftm library file added and small bug fix in FTM test bench


10:17 Changeset [10126] by weitzel
Test_PixelMap.txt deleted from repository
08:03 Changeset [10125] by ogrimm
DAQ page shows message service of drsdaq or FADctrl


16:09 Changeset [10124] by weitzel
FTM firmware documentation v3.0 added


17:10 Changeset [10123] by neise
jumper selectable MAC and IP address choice. D_T7 jumper selects if in_can (no jumper) or not in cam(jumper set) D_T6 jumper selects if in Dortmund (jumper set) or at ETHZ (jumper not set)
08:38 Changeset [10122] by neise
added missing files trigger_manager and some hds files to repos
08:32 Changeset [10121] by neise
synchronous trigger handling added continous soft trigger generation. ---> control frequency via 'send 0x21??' each step increases trigger delay by 12.5ms 0x2100 = 40Hz 0x21FF = 0.3Hz
08:13 Changeset [10120] by ogrimm
Moved OpenOtherSockets() to FADBoard class


12:41 Changeset [10119] by ogrimm
Bias has two commands for setting voltage: 'pixel' and 'channel'
09:47 Changeset [10118] by ogrimm
Adapted various programs to new PixelMap class


16:48 Changeset [10117] by ogrimm
Amplitude calibration integrated into event loop
12:04 Changeset [10116] by weitzel
new version of pixelmap class
09:52 Changeset [10115] by tbretz
Reordered the classes in MAvalanchePhotoDiode.h to make it compile.
08:47 Changeset [10114] by ogrimm
Event data can be written to disk in M0 format with command take


15:46 Changeset [10113] by ogrimm
Event thread informed through pipe of new incoming data
13:54 Changeset [10112] by ogrimm
Added persistance mode to event scope


20:08 Changeset [10111] by tbretz
Forgot it in my commit 2011/01/07.
15:46 Changeset [10110] by lutz
two empty lines deleted :-)
15:44 Changeset [10109] by lutz
niculin & dom debugged quite some stuff
15:41 Changeset [10108] by lutz
just a test
13:11 Changeset [10107] by ogrimm
hv command crashed when no bias board present


12:42 Changeset [10106] by neise
Niculin changed something in the presentation of the data


16:16 Changeset [10105] by ogrimm
Fixed warning if alarm server down
15:42 Changeset [10104] by weitzel
FTM_test9 added: check FTM-FTU communication
09:19 Changeset [10103] by neise
supports trigger disable & enable. enables during init.
07:46 Changeset [10102] by neise
- still testing - AD7719 and ATmega ADC work muxers as well output via USB


11:56 Changeset [10101] by ogrimm
Amplitude calibration information stored in file


20:39 Changeset [10100] by ogrimm
Amplitude calibration debugged
14:44 Changeset [10099] by ogrimm
Corrupt events (wrong start-package flag) are removed from internal buffer
12:49 Changeset [10098] by neise
bug in last commit fixed
12:40 Changeset [10097] by neise
switching SCLK ON and OFF during acalib-process
12:06 Changeset [10096] by ogrimm
Small changes to limit error messages in case crate communication breaks
11:43 Changeset [10095] by neise
DRS shift register init is now done by the FAD firmware --> init procedure changed
10:20 Changeset [10094] by neise
initial commit of FSC firmware - use for FSC testing only -
Note: See TracTimeline for information about the timeline view.